基于液体静压导轨的大行程快刀伺服系统设计

采用了理论设计和有限元仿真分析相结合的方法,设计了基于液体静压导轨的大行程快刀伺服系统(最大加工行程30mm,行程4mm时频响不低于50Hz).首先,设计得到了基于液体静压导轨的大行程快刀伺服系统的结构模型和相关参数;接着,利用ANSYS/FLUENT软件对液体静压导轨的变形、模态以及油膜压力分布进行仿真分析,并且将油膜刚度的理论计算值和仿真计算值进行比较,验证了导轨设计的可靠性;最后,选用能够满足要求的音圈电机、位置反馈装置以及功能强大的MPAC运动控制器等完成了控制系统的搭建.     

仿真代理在导弹制导半实物仿真试验系统中的应用

针对独立运行的导弹制导半实物仿真试验系统接入联合试验系统的问题，应用了仿真代理的方法。在对原有系统控制关系进行最小化的改造前提下，通过控制接口的转换，实现了半实物仿真试验系统与其它异类异构系统之间的互联，拓展了半实物仿真试验系统的应用。     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

某型教练机嵌入式训练系统顶层设计技术研究

本文通过对该型教练机现有航空电子系统构型、驾驶员操作程序、接口控制文件深入研究,结合未来功能扩展需求,给出了合理的系统构型分析、功能分配、数据流规划、原相关系统软件改动分析,在此基础上还设计出了嵌入式训练系统技术方案.依据方案研制的嵌入式训练系统原理样机通过系统动态试验、航电系统地面综合试验和飞机地面通电试验,证明系统...     

8mm Dicke辐射计波形仿真研究

采用System view软件对从输入到天线的噪声信号到A/D采样之前的各个模块和辐射计线性度进行了波形的仿真研究,仿真结果和实际相符合,对辐射计的硬件实现提供了很好的指导作用。     

Avoid online radiation risk: Theoretical simulation of chromosome breaks in cells exposed to heavy ions

In this study, we report an easy and quick method on simulating chromosome breaks in cells exposed to heavy charged particles. The theoretical value of chromosome break was calculated, and validated comparison with experimental value by using premature chromosome condensation technique. A good consistency was found between theoretical and experimental value. This suggested that higher relative biological effectiveness of heavy ions was closely correlated with its physical characteristics. Also, a safe approach on predicting chromosome breaks in cells exposed to heavy ions at off-line environment can be considered. Furthermore, three key factors influencing the theoretical simulation was investigated and discussed.     

可变形翼战术导弹飞行动力学联合仿真研究

基于集中质量假设发展的一套适于可变形翼导弹的多体运动模型,以附加惯性项及快变气动参数的形式来反映弹翼变形对导弹动态特性的影响,涉及交叉求解不同弹翼外形对应的气动特性及运动方程.由此提出的一种基于Missile DATCOM与MATLAB/SIMULlNK的联合仿真方法,应用于典型轴对称导弹的变翼动态特性研究中,快速有效...