腐蚀对sic/Al(L2)和sic/Al-Ni复合丝力学性能的影响~①

本文对SiC/Al(L2)和SiC/A1-Ni复合丝在蒸馏水和在3.5％NaCl溶液中的耐腐蚀性能进行了研究。通过测试腐蚀前后复合丝的抗拉强度,利用气相色谱、发射光谱、X射线衍射等手段分析腐蚀气体和腐蚀产物,观察金相和扫描电镜下形貌的变化,发现SiC/A1复合丝在室温蒸馏水中36天、50℃和75℃蒸馏水中各15天浸泡后,其抗拉强度基本保持不变,说明该类复合材料对潮湿环境具有良好的耐腐蚀性能;SiC/A1-Ni复合丝在3.5％NaC1溶液中浸泡后,其抗拉强度随溶液温度升高和时闻延长而逐渐下降;其腐蚀主要是选择性腐蚀,其次是孔蚀和缝隙蚀。     

碳/环氧复合材料模压成型工艺特性及其影响性能主要因素

文章介绍了碳/环氧复合材料模压成型工艺特性,并讨论了影响模压成型制品性能的主要因素等内容。     

镁铝富燃料推进剂燃烧残渣影响因素理论分析

用最小自由能法计算了镁铝富燃料推进剂一次燃烧室产物的成分,分析了凝聚相C、Mg和A l产物含量的变化对燃烧残渣的影响;主要探讨了AP含量、Mg/A l比例、HTPB粘合剂含量、燃烧室压强对凝聚相C、Mg、A l燃烧产物含量的影响。计算结果表明,增加AP含量、设计Mg/A l比小于3/5、减小HTPB粘合剂含量、降低燃烧室压强均能减少凝聚相产物含量,有利于降低燃烧残渣。燃气发生器实验结果表明,Mg/A l比例对燃烧残渣影响的实验数据与理论分析一致。     

一种典型C/SiC构型件的热噪声适应性试验研究

航天器结构用新型C/SiC复合材料在飞行过程中会承受气动加热和噪声复合环境,容易出现疲劳破坏,需要进行地面热噪声试验考核。针对一种典型的C/SiC蒙皮骨架构型件,利用行波管开展热噪声试验研究,对试验件、试验装置和试验方法等进行介绍。利用试验获得的有效数据揭示热噪声复合环境下该C/SiC构型件的失效模式,验证其热噪声环境适应性。     

流变铸造法制备Al_2O_（3P）／ZA4－3复合材料的研究

为提高模用锌合金ＺＡ４－３的性能，扩大其应用范围，本项工作采用流变铸造法成功地制备了性能稳定的Ａｌ２Ｏ３Ｐ／ＺＡ４－３复合材料。对该材料进行了弯曲强度、冲击韧性、压缩强度、硬度及耐磨性等性能试验，结果表明：Ａｌ２Ｏ３ｐ的加入，使锌合金的压缩强度、室温和高温硬度以及耐磨性明显提高，其弯曲强度略有降低，而其冲击韧性下降了　。最后还讨论了成形工艺参数、颗粒含量和颗粒直径对该复合材料性能的影响。     

载人飞船返回舱着陆待援段换热性能研究

在对载人飞船着陆待援段返回舱换热过程中各传热途径的量级范围及影响因素进行计算分析和对比的基础上,简化返回舱传热模型,提出返回舱综合换热系数的概念;并通过载人飞船返回舱换热试验对理论分析进行了验证,获取了返回舱综合换热系数的工程数据,所获数据可用于实现长时间地面待援期间返回舱内热环境的快速预示。     

纺丝工艺对炭纤维缠绕复合材料强度转化率的影响

通过不同纺丝工艺的聚丙烯腈基炭纤维表面状态、NOL环及Φ150 mm容器的实验研究,分析了不同纺丝工艺对湿法缠绕复合材料聚丙烯腈基炭纤维强度转化率的影响。结果表明,干喷湿纺炭纤维比湿法纺丝Φ150 mm容器环向纤维强度转化率要高出11.9%~15.4%,湿法纺丝的炭纤维复合材料NOL环层间剪切强度要比干喷湿纺炭纤维复合材料高7.4~34.1 MPa。因此,干喷湿纺的炭纤维可应用于固体火箭发动机缠绕壳体、压力容器等主要承受拉伸应力的领域,可充分发挥其纤维强度;而湿法纺丝工艺制成的炭纤维与树脂基体结合紧密,利于载荷的传递,可应用于承受压缩剪切等复杂载荷的领域,从而发挥这两种纤维各自不同优势。     

复合材料叠层结构剖面翘曲修正理论

 首先假设复合材料叠层结构的面内位移沿厚度方向为直线分布,然后根据剪切变形进行连续修正,获得逐步升高的各阶翘曲位移分布函数。文中以叠层梁为例,应用最小势能原理导出其静力方程和力的边界条件。在长度方向则采用升阶谱位移函数,进行了数值计算。所得叠层梁的位移和应力分布的数值结果与精确解相比,表明本文方法有很好的收敛性。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced AI Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced AI-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction reinforced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.