金属水反应水冲压发动机系统性能估算

使用金属／水反应燃料是推进水下超高速航行器的最佳途径，分析了单次注水和二次注水的铝／水反应燃料水冲压发动机系统，得出了燃料质量配比、燃烧室温度、燃烧室压强、系统有效推力、效率等关键技术性能指标。指出了二次注水系统的优越性并提出了一种二次注水系统的实施方案。分析结论与实际系统性能指标相吻合，证明了分析的正确性，可以为系统研究提供参考。     

氢燃料双模态冲压模型发动机M6的试验研究

笔者研究了一个有突扩台阶的氢燃料高超声速冲压发动机模型的气体动力学特性和推力特性。氢气从位于燃烧室突扩台阶后的支板逆来流喷注,测量了氢气燃烧状态下模型发动机壁面的压力分布和推力收益数据。实验结果表明,在氢气的当量油气比为0.35～0.8的范围,在本模型流道构型条件下,氢气自燃,并随当量油气比的增加,燃烧室内压力增加,获得的推力收益增大,最大推力收益达到500N。实验在CARDC的脉冲燃烧风洞中进行,实验马赫数为6,总温1850K,总压5.5MPa。     

铸造SiCp／ZL101复合材料的组织与性能

本文利用半固态搅拌铸造法制备了ＳｉＣｐ／ＺＬ１０１复合材料，对其组织和某些性能进行了研究，结果表明：ＳｉＣｐ在基体中分布均匀，无严重团聚现象，与基体结合良好，与基体合金相比，耐磨性，硬度有显著提高。     

低温度系数标准电阻器的研制

主要介绍了低温度系数标准电阻器的研制,包括采用的电阻合金材料、电阻合金材料的筛选、匹配与加工制作,低温度系数标准电阻器的技术参数、温度系数测量方法,减小温度系数采用的补偿方法,测试结果分析。     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.     

某型航空活塞发动机曲轴喷油螺钉的维修工艺研究

喷油螺钉是某型航空活塞式发动机曲轴组合中的重要零件，单纯采用超声波清洗难以清除该零件内部积炭。结合生产实践对工艺进行改良，使该零件修理后的抽检合格率由20%提升至70%，缩短了发动机的翻修时间，节约了维修成本。     

Satellite launch vehicle effect on the Earth’s lower ionosphere: A case study

The effect of the rocket exhaust products on the D-region of the ionosphere is investigated with the help of Very low frequency (VLF) electromagnetic wave propagation characteristics within the Earth-ionosphere waveguide. The changes in the electron density profile are computed from the observed VLF signal amplitude perturbations about 3 dB during the rocket launch. We find a localized electron depletion in the lower ionosphere at an altitude of around 58 km, that is thought to be originated by the attachment of ionospheric ion and molecular hydrogen along with water molecule in the exhaust product of first stage burn of Geosynchronous Launch Vehicle (GSLV) rocket at the time of GSLV launched from Sriharikota, India, on 27 August 2015 at 11:22 UT (16:52 IST). The ionospheric depletion perturbed the navigational VLF signal (VTX = 17 kHz) 134 s after the launch of the GSLV rocket.     

对空间碎片近距随遇悬停的控制方法及悬停燃耗分析

对空间碎片检视或抓捕操控中的悬停控制及燃耗问题进行了研究。通过C W方程，建立任务星近距随遇定点悬停控制模型，通过设计状态反馈控制器分析定点悬停的可控性以及推控要求，结果表明近距悬停需要与悬停位置相关的两个正交方向上的常值连续推力控制量，以及用于抵抗扰动的三轴向上的反馈变推力控制量。分析了近距随遇悬停的推控分系统配置，建立了长时近距随遇悬停的燃耗及燃耗速率的数学模型，最后分析了既满足安全距离需求、又满足悬停方位需求的最小悬停燃耗模型。     

某型飞机通信电台干扰油量系统故障分析

针对某型飞机通信电台干扰油量系统故障，分析了油量测量系统的原理和电磁干扰机理，研究了故障发生的原因，制定了抑制干扰的措施，解决了一直困扰修理的油量指示系统跳变问题，提高了飞机修理质量。     

用于分级燃烧的高性能燃油分配器的改进设计与仿真

为了提高燃料使用效率、降低污染物排放,在已有分级燃烧燃油分配器基础上,针对航空发动机双环腔燃烧室改进设计了1种高性能燃油分配器。简述了分级燃烧燃油分配器的工作原理,建立了其AMESim模型。根据设计要求,通过仿真验证了燃油分配器的稳定性、分配比与输入信号的稳态关系,计算了燃油分配器输出与燃油分配计划表之间的误差,分析了燃油分配器的动态特性以及对外部参数变化的鲁棒性,并且针对该分配器的非线性特性提出了解决办法。仿真结果表明：与文献[4]所设计的燃油分配器相比,改进设计的燃油分配器鲁棒性更好,稳态和动态性能更优。