Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

摄影景深控制的几个技术问题

本文论述了三种景深控制形式与艺术内容表现、艺术价值创造的关系。     

铸造SiCp／ZL101复合材料的组织与性能

本文利用半固态搅拌铸造法制备了ＳｉＣｐ／ＺＬ１０１复合材料，对其组织和某些性能进行了研究，结果表明：ＳｉＣｐ在基体中分布均匀，无严重团聚现象，与基体结合良好，与基体合金相比，耐磨性，硬度有显著提高。     

低温度系数标准电阻器的研制

主要介绍了低温度系数标准电阻器的研制,包括采用的电阻合金材料、电阻合金材料的筛选、匹配与加工制作,低温度系数标准电阻器的技术参数、温度系数测量方法,减小温度系数采用的补偿方法,测试结果分析。     

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

Analyses toward factors influencing sealing clearance of a metal rubber seal and derivation of a calculation formula

Sealing clearance is a key factor for a metal rubber seal’s sealability. The expansion coef-ficient and expansion deformation in the radial direction of metal rubber have been obtained through a thermal expansion experiment of metal rubber. The influence of the elastic modulus to the sealing clearance has been analyzed theoretically. By combining the temperature and elasticity factors of metal rubber with the elastic mechanics theory, the calculation formula of the sealing clearance has been derived, and the values of the sealing clearance and the leakage rate in certain working conditions have been calculated. Experimental results are consistent with calculation results in a high degree. The calculation formula of the sealing clearance can explain the influences of the temperature and elastic modulus factors of metal rubber on the sealing clearance. It can pro-vide guidance for the study of sealing mechanism of metal rubber seals.     

航空机载谐振膜式密度传感器的研究

针对飞机飞行中燃油量的在线实时测量需求.设计了基于谐振原理的新型谐振膜式液体密度传感器.对谐振膜片进行了数学模型分析,并设计了基于数字闭环方法的谐振膜式密度传感器整体结构.试验结果表明,该传感器测量精度较高,稳定性较好,结构简单,便于加工,能满足航空煤油在线实时测量的需求.     

锥柱形加筋金属膜片变形的数值仿真分析

概述了金属膜片贮箱膜片结构的研究现状,提出了锥柱形加筋膜片整体结构变形问题。根据试验情况建立了该膜片的有限元模型,并基于非线性有限元软件MSC.Marc进行了数值模拟,分析了膜片结构的变形过程和变化规律,通过对加筋结构的分析解释了膜片变形的机理,得到了一些控制膜片失效的方法。     

电热破膜激波管及其PLIF测量系统的研制

探讨了用Nd:YAG脉冲激光器作为泵浦光源对激波管内瞬态非定常流场进行平面激光诱导荧光(Planar laser induced fluorescence,PLIF)测量的时序同步问题.由于该激光器需要预热以获得稳定的倍频输出,作者研制了低压大电流的电热破膜装置,实现对激波产生时机的控制.在大尺寸矩形截面的激波管上搭建了PLIF测量平台,并在此平台上进行了丙酮示踪流场显示和氢氧基分布测量.     

金属工艺学课件的设计与制作

计算机辅助教学是计算机发展的新领域。本文主要介绍了金属工艺学课件的设计制作思路 ,制作的素材 ,它是传统课堂教学的有益补充