轴对称跨音速流中无激波超音速区的设计

本文直接从音速线出发计算了一个旋成体跨音速绕流超音速泡中的特征线网。提出了从音速线开拓到一条超音速线的方法,计算了无旋轴对称流的特征线网,发现其特点是不能跨越对称轴线,并对其原因作了初步的讨论。本文的计算结果可应用于物面修形。     

防止Ⅱ型驾驶员诱发振荡技术的研究

许多严重的飞行事故都与由速率限制引起的Ⅱ型PIO有关。针对如何预防PIO，首先介绍了自适应杆增益和软件限制环节的设计原理。然后以某带速率限制的电传飞机为例，运用同一理论，分析采用自适应杆增益和软件限制环节来改善速率限制的不利影响。仿真结果表明，自适应杆增益环节和软件限制环节都能抑制住PIO的发生，但两者组合加入抑制效果更好，飞行品质也能达到满意的程度。     

冲击响应谱（SRS）分析数字化方法探讨

本文介绍了求单自由度二阶系统冲击响应谱（ＳＲＳ）的几种常用的数字化分析方法：直接积分法；快速富氏变换（ＦＦＴ）法；递推法；数字滤波器方法；改进的数字滤波器方法。并比较了它们的优缺点。     

基于冗余伪观测的自适应滤波算法

现有的二阶互差分(SOMD)算法能够给出与状态估计误差解耦的观测噪声协方差估计，但是需要满足冗余测量的条件，但这一条件往往难以满足。 针对这一问题，提出了一种利用状态预测值构造相邻2个时刻伪观测的方法，将原SOMD算法扩展到具有单测量的系统中。使用目标跟踪问题对该算法的有效性进行验证。仿真结果表明，当采样周期较小时，该算法能够忽略状态估计误差的影响并给出较准确的观测噪声方差，在精度和鲁棒性方面优于其他参考算法。     

用非线性模型分析气动液阀的启动特性

对气动液阀的启动过程建立了非线性数学模型,分析了尺寸参数和推进剂进、出口压力对该阀的启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下,适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径,降低推进剂进口和出口的压力有利于提高该阀的响应能力。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

飞机座舱有机玻璃机械加工应力测量方法研究

 通过实验研究了有机玻璃由于机械加工所产生的双折射条纹的性质及其与机械加工应力的关系;建立了一种定量测定和无损检测平板有机玻璃和飞机座舱有机玻璃件机械加工应力的新方法:用光弹性仪可以测得与双折射有关的干涉条纹,则可确定加工应力。     

美陆军制导武器试验半实物仿真技术综述

主要综述美国陆军制导武器试验的仿真技术和设施，同时介绍仿真试验中使用的几种典型的目标景象投影技术，并说明了它们的应用范围和优缺点。最后介绍了当前制导武器试验仿真技术的发展趋势。     

TiFe0．86Cr0．1／NaM复合贮氢材料的合成与性质

 利用蒸汽相法制备沸石技术合成ＴｉＦｅ０．８６Ｃｒ０．１／ＮａＭ复合贮氢材料的各种条件,找到了较适宜的碱度ＳｉＯ＿２／Ａｌ＿２Ｏ＿３以及合金与沸石。研究了合成条件对贮氢容量的影响,结果表明,沸石为单一晶相合成粒度不低于７４μｍ为佳。同时,该材料亦表现出良好的抗Ｏ＿２、ＣＯ＿２中毒特性。