Time and phase synchronization using clutter observations in airborne distributed coherent aperture radars

Airborne Distributed Coherent Aperture Radar(ADCAR) is one of the most promising next-generation radars to significantly improve target detection and discrimination abilities. However, time and phase synchronization among unit radars should be done before an ADCAR is intended to cohere on a potential target. To address this problem, a time and phase synchronization technique using clutter observations is proposed in this paper. Clutter returns from different azimuths and elevations on the surfac...     

俯仰敏捷性评估与影响因素研究

建立了现代高机动性能战斗机俯仰敏捷性仿真计算数学模型和机动飞行时的操纵动作，以Ｆ－１６战斗机为例，计算并讨论了初始飞行状态以及飞行控制系统参数对战斗机俯仰敏捷性的影响。结果表明，选择适当的飞行状态，有利于更好地发挥飞机的俯仰敏捷性；降低飞机整体系统的阻尼，将有利于提高飞机的俯仰敏捷性；控制系统有关参数的设计，除考虑飞行品质要求外，还需综合考虑飞机敏捷性等方面的要求。     

飞机液压系统管路设计分析

飞机液压系统管路设计，应考虑导管材料、直径和壁厚的选择及系统工作压力、介质流量与工作环境相适应，既要保证导管有足够的强度，又要使系统重量最轻，寿命可靠性高。这里从导管管径设计、壁厚确定、爆破压力和管路安装等方面对飞机液压管路系统的设计作了分析，提供了导管设计的计算方法。     

低轨巨型星座网络容量评估与分析

低轨卫星网络可以提供广覆盖、低时延、大容量的通信服务和随遇接入的网络服务,可有效弥补地面通信网络和高轨卫星网络的不足。近年来“星链”“一网”等星座项目推动了低轨巨型星座的飞速发展。卫星网络容量是网络性能评价的重要指标,传统方法计算复杂度高、耗时长,且计算开销随网络节点数迅速增加,在巨型星座网络评估中产生巨大计算开销。面向低轨巨型星座网络容量评估问题,提出了一种基于最大流的网络容量评估方法,与传统方法相比计算复杂度和计算耗时大大降低。以“星链”星座为例,分析了星座构型、星间链路拓扑连接方式、链路容量及用户需求量对巨型星座网络容量的影响。仿真分析结果对未来低轨巨型星座网络建设具有指导意义。     

立方星电源系统最大功率点跟踪优化控制方法

针对立方星在能量来源严重受限条件下如何提高太阳能利用率的难题,提出一种适用于立方星的集中供电式空间微电源架构(EPS),并设计基于改进粒子群优化算法的最大功率点跟踪(MPPT)控制策略来提升能量转换效率。首先,推导太阳电池阵列的数学模型,并根据太阳电池阵列的工作特性,提出电源系统最大功率点跟踪控制的物理系统实现结构。其次,设计基于改进粒子群优化(PSO)的最大功率点跟踪控制算法,并进行了数学仿真校验。最后,对所设计的电源系统架构进行了硬件实现和试验验证。地面试验结果表明,电源系统的太阳能最大转换效率可达95.5%。该电源系统成功应用于世界首颗12U立方星“翱翔之星”的飞行试验,在轨数据表明电源系统工作状态良好,为微纳卫星电源系统的设计提供了有益参考。     

Prediction of cutting forces in flank milling of parts with non-developable ruled surfaces

Predicting the cutting forces required for five-axis flank milling is a challenging task due to the difficulties involved in determining the Undeformed Chip Thickness(UCT) and CutterWorkpiece Engagement(CWE). To solve these problems, this paper presents a new mechanistic cutting force model based on the geometrical analysis of a flank milling process. In the model,the part feature and corresponding cutting location data are taken as input information. The UCT considering cutter runout is calculated according to the instantaneous feed rate of the element cutting edges. A solid-discrete-based method is used to precisely and efficiently identify the CWE between the end mill and the surface being machined. Then, after calibrating the specific force coef-ficients, the mechanistic milling force can be obtained. During the validation process, two practical operations, three-axis flank milling of a vertical surface and five-axis flank milling of a nondevelopable ruled surface, are conducted. Comparisons between predicted and measured cutting forces demonstrate the reliability of the proposed cutting force model.     

一种基于云模型优化的飞行器参数辨识算法

极大似然估计方法(ML)在飞行器参数辨识中得到了广泛应用,该方法需要预先推导灵敏度方程,进而求解灵敏度矩阵,在应用过程中比较繁杂,且容易陷入局部最优。提出一种基于云模型优化的飞行器参数辨识算法,根据极大似然估计原理,利用云模型的优化理论对极大似然函数进行优化,从而得到待辨识参数值。该算法不必推导灵敏度矩阵,对初值要求不高,应用便捷,且保留了云模型优化的特点,收敛速度较快、不易陷入局部最优。以Twin Otter飞机为例对算法进行验证。结果表明:算法易于实现、辨识结果精度较高、收敛速度较快,不易陷入局部最优。     

Performance investigation of intercooler operating in wet condition using distributed parameter model

The performance of a marine gas turbine intercooler operating in wet condition was evaluated.The intercooler was a cross-flow plate-fin heat exchanger that used air and pure water as its working fluids at the hot and cold sides,respectively.The heat transfer performance and the water vapor condensation were investigated for a relative humidity of the inlet air that reached 100% during warship cruise.The condensation of the water vapors increased the hot side outlet temperature by a certain amount,which could in turn influence the performance of the compressor downstream.The condensate film thickness and the void fraction were calculated based on an annular two-phase flow model.It is found that water vapor condensation in hot flow channel increases the outlet temperature with a maximum value of 7.3℃ in the case of 100% relative humidity.The calculated liquid film thickness reaches a maximum value of 4μm,which indicates negligible thermal resistance to heat transfer.The results of liquid film thicknesses also provide a qualitative prediction of the diameter distribution of the condensate water droplets.     

Cutting force prediction for circular end milling process

A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cutting conditions, especially for circular milling process. This paper presents an improved cutting force model for circular end milling process based on the typical linear milling force model. The curvature effects of tool path on chip thickness as well as entry and exit angles are analyzed, and the cutting force model of linear milling process is then corrected to fit circular end milling processes. Instantaneous cutting forces during circular end milling process are predicted according to the proposed model. The deduced cutting force model can be used for both linear and circular end milling processes. Finally, circular end milling experiments with constant and variable radial depth were carried out to verify the availability of the proposed method. Experiment results show that measured results and simulated results corresponds well with each other.     

应用最大熵谱估计检测微弱信号

频谱分析是数字信号处理的主要内容之一 ,近年来 ,由于最大熵算法的一些优点 ,使它成为现代谱估计中一个比较活跃的领域。最大熵算法是 196 7年由Burg提出来的一种现代谱估计方法。提出了应用最大熵谱估计及LMS自适应算法 ,根据有限数据 ,在频域内提取被淹没在噪声中的有用信号的方法及应用MATLAB语言进行的仿真。