大飞机工装数字化生产线

大飞机的研制质量和周期很大程度上依赖于工艺装备(工装)的设计制造质量和周期.通过集成工装设计、制造、管理技术,构建飞机工装数字化生产线,实现工装研发过程各环节数据流的畅通,才能充分发挥数字化技术在工装研发过程中的作用.中航飞机西安飞机分公司的大飞机工装数字化生产线的应用实践表明,在数字化环境下,机床的加工效率显著提高,工装返工数量大幅下降.     

铜铬复合电极电火花小孔加工机理及试验研究

电火花小孔加工中存在工具电极损耗严重、加工速度慢、棱角变钝出现锥度等问题。分析其存在问题的原因,提出采用铜铬复合电极进行电火花小孔加工。分析其加工机理并进行实验,实验结果表明:采用铜铬复合电极进行小孔加工比采用铜电极进行小孔加工能显著提高加工速度,减小锥度和电极相对损耗。     

Predictive Modeling and Parameter Optimization of Cutting Forces During Orbital Drilling

To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital drill holes in aluminum alloy 6061.Firstly,four cutting control parameters(tool rotation speed,tool revolution speed,axial feeding pitch and tool revolution radius)and affecting cutting forces are identified after orbital drilling kinematics analysis.Secondly,hybrid level orthogonal experiment method is utilized in modeling experiment.By nonlinear regression analysis,two quadratic prediction models for axial and radial forces are established,where the above four control parameters are used as input variables.Then,model accuracy and cutting control parameters are analyzed.Upon axial and radial forces models,two optimal combinations of cutting control parameters are obtained for processing a13mm hole,corresponding to the minimum axial force and the radial force respectively.Finally,each optimal combination is applied in verification experiment.The verification experiment results of cutting force are in good agreement with prediction model,which confirms accracy of the research method in practical production.     

基于加工能力模糊聚类的设备分组方法

为了在工艺设计中高效、合理、准确地确定加工设备,实现资源优化配置,提出了基于加工能力模糊聚类的设备分组方法.该方法采用加工能力元描述设备的加工能力,通过对加工能力元的聚类分组,实现对设备的分组.在此基础上,建立了加工能力元的数学模型,采用区间数模糊C-均值聚类算法对模型进行了求解,并采用改进的最大最小距离算法产生初始分组中心.最后,通过具体实例,验证了该方法的有效性.     

基于激光旋切法的陶瓷材料盲孔加工方法研究

介绍了激光打孔的基本原理,对激光能量、离焦量、轨迹在激光旋切法加工盲孔过程中对孔形和表面质量的影响进行了分析和试验验证,并给出了一般规律.依据试验结果确定了合理工艺参数,采用旋切法在碳纤维增强碳化硅陶瓷基复合材料（Cf/SiC）上打出了孔径为1 mm,孔深为1.1 mm,锥度小于15°的盲孔.     

数控加工零件热场分布的虚拟仿真

利用有限差分法对金属零件在数控机械加工过程产生热量的分布进行了数值分析,为计算金属零件热应力变形提供基础,是虚拟制造中机械加工工艺过程规划虚拟仿真的一种新方法。     

声发射监测钻头折断的实验研究

 金属切削过程中会发出声讯号。用声发射技术监测刀具破损是一个很有潜力的新方法。本文研究了声发射技术在钻头折断在线监测中的应用。实验结果表明,所设计的实验监测系统能可靠地监测钻头的折断,并可提前预报直径大于1.5mm钻头的折断。     

展成电解加工整体叶轮扭曲叶片中的间隙分析

叙述了展成电解加工整体叶轮扭曲叶片中间隙的计算方法,并讨论了工件和阴极各运动速度对间隙的影响。     

镍基单晶高温合金DD6气膜孔热机械疲劳试验

涡轮冷却叶片气膜孔边存在大应力梯度,且服役时承受交变的机械载荷和热载荷,热机械疲劳（TMF）是其主要失效模式。通过开展带气膜孔和不带气膜孔的薄壁圆管试件TMF试验研究了气膜孔对镍基单晶高温合金TMF寿命的影响。结果表明最大循环应力在300~500 MPa应力范围内,循环应力幅值与镍基单晶高温合金TMF寿命呈现良好的对数线性关系,且气膜孔导致镍基单晶高温合金TMF寿命下降可达82.5%。继而完成了横向取向分别为〈010〉、〈110〉方向的气膜孔模拟件试验,结果表明气膜孔取向为〈110〉时寿命最短,仅为〈010〉取向的40.0%。最后开展了不同制孔工艺下的气膜孔模拟件试验,结果表明激光制孔气膜孔模拟试件寿命仅为电液束制孔气膜孔模拟试件的54.0%。气膜孔模拟件断口分析表明:TMF裂纹均萌生于气膜孔边,源区氧化严重;裂纹沿着大致与气膜孔边垂直的方向扩展。      

Prediction of cutting forces in flank milling of parts with non-developable ruled surfaces

Predicting the cutting forces required for five-axis flank milling is a challenging task due to the difficulties involved in determining the Undeformed Chip Thickness(UCT) and CutterWorkpiece Engagement(CWE). To solve these problems, this paper presents a new mechanistic cutting force model based on the geometrical analysis of a flank milling process. In the model,the part feature and corresponding cutting location data are taken as input information. The UCT considering cutter runout is calculated according to the instantaneous feed rate of the element cutting edges. A solid-discrete-based method is used to precisely and efficiently identify the CWE between the end mill and the surface being machined. Then, after calibrating the specific force coef-ficients, the mechanistic milling force can be obtained. During the validation process, two practical operations, three-axis flank milling of a vertical surface and five-axis flank milling of a nondevelopable ruled surface, are conducted. Comparisons between predicted and measured cutting forces demonstrate the reliability of the proposed cutting force model.