Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

一种大面积比喷管的分段式设计与数值分析

为了满足大推力上面级发动机大面积比喷管的设计需求,采用了排放冷却前段和单壁辐射冷却尾段的分段式设计方案。在排放冷却前段传热计算的基础上,通过对内流场进行数值模拟,重点研究了单壁尾段在引入上游排放冷却气氢情况下的冷却特性和喷管效率。结果表明:对于大面积比喷管,采用带二次流的单壁金属喷管延伸段是现实可行的,有望达到较好的冷却保护效果并提高喷管效率。     

A theoretical model of semi-elliptic surface crack growth

A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.     

含噪信号经验模式分解虚假分量识别方法

针对含噪信号Hilbert-Huang变换存在虚假分量,提出改进的奇异值分解(SVD)方法进行降噪,改进包含两个部分:一是利用重构相空间代替传统矩阵如Hankel矩阵,以去掉信号冗余,再者提出奇异值能量熵分量差分法,更易于定出重构奇异值阶次;二是提出了频谱比值法对虚假分量进行辨识,更有效辨识出虚假分量.首先利用经验模式分解(EMD)得到本征模式分量(IMF),识别并剔除趋势项,重构信号,然后进行SVD,重构降噪后的信号,消除虚假分量,最后进行时频分析.联合方法应用于含噪仿真信号,信噪比(signal noise ratio,SNR)提高了5.5%,虚假分量辨识率提高至100%,用于双跨转子故障振动信号,得到正确的时频结果,表明了所提方法识别含噪信号虚假分量的有效性.     

肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

轻质隔热纳米孔结构耐烧蚀酚醛材料

在一定温度下,通过改性剂组分与热固性钡酚醛树脂之间热共聚反应,制备了改性酚醛树脂。采
用模压工艺制备出具有目标尺寸和形状的改性酚醛树脂固化物,对该样品分别进行了400 和700℃的炭化处
理,得到了相应的酚醛炭化样品,并测试其密度、失重率、收缩率等特征参数。研究改性剂用量对碳化物特征参
数和性能的影响,如密度、失重率形貌、比表面积、隔热性能、压缩强度等。SEM 研究表明,700℃炭化后样品形
成了“珊瑚状”碳结构,形成了30 ~150 nm 纳米孔。比表面积测试(BET)结果表明其比表面积可达464 m2 / g。
隔热性能与力学性能的测试结果表明,相对于未改性酚醛树脂碳化物,改性酚醛碳化物的热导率降低了
45． 57%,并且保持了较好的压缩强度。     

飞机下滑波束导引系统设计及仿真

下滑波束导引系统是飞机在自动着陆时所采用的一种重要无线电波束导引系统。首先,简要阐述了下滑波束导引系统的基本工作原理;然后,对导引系统的运动学环节及下滑耦合器进行分析,对飞机下滑波束导引系统结构进行设计;最后,在MATLAB平台下,对所设计的下滑波束导引系统进行大量仿真研究。仿真结果显示。所设计的下滑波束导引系统结构是合理的,其控制系统是稳定的,且其稳态性能也得到改善。     

One-to-one relationship between low latitude whistlers and conjugate source lightning discharges and their propagation characteristics

One-to-one relation with its causative lightning discharges and propagation features of night-time whistlers recorded at low-latitude station, Allahabad (geomag. lat. 16.05°N, L = 1.08), India, from continuous observations made during 1–7 April, 2011 have been studied. The whistler observations were made using the Automatic Whistler Detector (AWD) system and AWESOME VLF receiver. The causative lightning strikes of whistlers were checked in data provided by World-Wide Lightning Location Network (WWLLN). A total of 32 whistlers were observed out of which 23 were correlated with their causative lightnings in and around the conjugate location (geom. lat. 9.87°S) of Allahabad. A multi-flash whistler is also observed on 1 April with dispersions 15.3, 17.5 and 13.6 s^1/2. About 70% (23 out of 32) whistlers were correlated with the WWLLN detected causative lightnings in the conjugate region which supports the ducted mode of propagation at low latitude. The multi-flash and short whistlers also propagated most likely in the ducted mode to this station.     

降低PLC系统峰均比的低复杂度改进SLM算法

针对信道慢时变特性及噪声复杂的特点,提出了适用于低压电力线通信的降低峰均比的改进算法.改进算法对原始输入序列中的部分数据进行循环移位来获得一系列不同的新数据序列;在每个新数据序列尾部插入相应的边带信息组成一个输入候选序列;对这一系列不同的输入候选序列分别实施傅里叶反变换,得到不同的输出序列;从中选择峰均比最小的用于传输,达到降低系统峰均比的目的.结果表明:改进算法能够有效地降低系统的峰均比,并且能够获得更好的误码率性能,同时具有比传统选择性映射方法更低的计算复杂度.     

Enhancing buckling capacity of a rectangular plate under uniaxial compression by utilizing an auxetic material

Auxetic materials have previously been shown to enhance various performances due to its unusual property of becoming fatter when uniaxially stretched and thinner when uniaxially com-pressed (i.e., the materials exhibit a negative Poisson’s ratio). The current study focuses on assessing the potential of an auxetic material to enhance the buckling capacity of a rectangular plate under uniaxial compression. The in-plane translational restraint along the unloaded edges that was often neglected in open literature is taken into consideration in our buckling model proposed in this study. The closed-form expressions for the critical buckling coefficient of the rectangle are provided and the predicted results agree well with those determined by the finite element method. Further-more, the results indicate that the buckling performance of a rectangular plate under uniaxial com-pression can be significantly improved by replacing the traditional material that has a positive Poisson’s ratio with an auxetic material when there is in-plane translation restraint along the unloaded edges.