喷注角度对超声速气流中液体横向射流的影响

为探索超声速气流中变角度组合射流对喷注雾化过程的影响，采用高速摄影和基于KH-RT破碎模型的欧拉-拉格朗日数值仿真方法开展研究，仿真结果和实验吻合较好。研究表明，同一流量下逆流喷注，可以较为有效地增强混合效果，提升射流穿透深度。带扩张型面内液雾穿透深度呈现先增大后降低的趋势。等流量条件下顺流双孔喷注有效截面面积大体一致，略低于单孔直喷。等效流量下逆流喷注所得液雾截面面积收益最为明显。截面平均粒径方面，单孔喷注雾化粒径基本一致，顺流双孔喷雾粒径较小。等压降顺流对喷由于流量较大，雾化质量相对较差，平均粒径最大。     

面向航天应用的液态金属相变传热性能研究

为探究液态金属相变材料的适用范围，本文使用数值模拟手段，比较分析了以镓为代表的低熔点金属与以正十八烷为代表的石蜡类相变材料之间的传热性能。结果表明，镓更适用于应对瞬时高热流冲击，即高热流、短时间工作的电子设备散热；而正十八烷适用于低热流、较长时间工作的电子设备控温。此外，单位体积相变材料，镓模块的热控时间长于正十八烷模块；单位质量相变材料，镓模块在短时间内占优，长时间内正十八烷模块占优。针对潜在应用场景进行分析，表明了液态金属相变材料可用于航天天线TR组件和激光器芯片控温。     

Development and coupling test of active spacecraft potential control – Next generation (ASPOC-NG)

The active spacecraft potential control (ASPOC) system developed in the 1990s emits positive ions to neutralise the spacecraft potential, such as used in several missions like Geotail, Equator-S, Cluster, Doublestar and MMS. With the experience gained, the next generation of the active spacecraft potential control (ASPOC-NG) instrument has been developed over the last three years. Thereby, three emission technologies were tested including Liquid Metal Ion Source (LMIS), Liquid Metal Electron Source (LMES) and Solid Metal Electron Source (SMES). The development of the emitter module by FOTEC and the corresponding electronics control unit by IWF is presented. Optimisations were carried out with the focus on the reduction of mass and power consumption to comply with the requirements of future scientific missions. Coupling tests of the modules and the electronics control unit were performed including range, accuracy and lifetime tests. Both ASPOC-NG instruments for positive and negative charge compensation and their performance values show excellent results.     

碳纤维特性对C/ C 复合材料界面性能的影响

分别采用扫描电镜、比表面积与孔体积分析仪等手段对日丝(RS-Cf ) 和美丝(MS-Cf ) 两种碳纤 维进行表面状态表征分析,通过纤维顶出试验、冲剪强度和弯曲强度对两种纤维制备的C/ C 复合材料界面性 能进行了微观和宏观测试,研究了不同表观结构纤维对C/ C 复合材料界面性能的影响。纤维表面形貌观察结 果表明:圆形RS-Cf 表面沟槽比腰果形MS-Cf 明显,但沟槽数量少于MS-Cf,而MS-Cf 的比表面积、孔体积和 孔径均大于RS-Cf。RS-C/ C、MS-C/ C 复合材料界面强度分别为2. 98 和3. 80 MPa;RS-C/ C 复合材料的弯曲 和冲剪强度分别为55. 9 和32. 0 MPa,低于MS-C/ C 复合材料的65． 0 和35. 2 MPa,微观和宏观力学性能均表 明MS-C/ C 复合材料的界面强度高于RS-C/ C 复合材料。     

Review of atomization mechanism and spray characteristics of a liquid jet in supersonic crossflow

The injection and atomization process of a liquid fuel jet is critical for an ignition start of a scramjet engine. Airwall-mounted crossflow injection strategy is widely used in scramjet combustors, avoiding high total pressure loss and allowing the liquid fuel to rapidly undergo atomization, mixing, and evaporation. In this review, research progress on a liquid jet in supersonic crossflow was evaluated from aspects of atomization mechanism and spray characteristics. When a liquid jet is injected into a supersonic crossflow, primary and secondary breakups occur successively. The surface instability of liquid can significantly affect the breakup process. This review discusses the current understanding of the breakup process and spray characteristics of a liquid jet in supersonic crossflow including the mechanism of atomization and the characteristics of distribution and atomization. The development of windward Rayleigh-Taylor (R-T) unstable waves is the main factor in column breakup. The development of Kelvin-Helmholtz (K-H) unstable waves along the circumferential direction of the jet or droplets is the main factor of surface and droplet breakups. The liquid–gas momentum ratio is the most important factor affecting the penetration depth. The span width of the liquid jet is affected by the windward area. Breakup and coalescence lead to a transformation of the size distribution of droplets from S- or C-shaped to I-shaped, and the velocity distribution of the droplets on the central symmetry plane has a mirrored S-shape. The droplet distribution on the spanwise cross-section retains a structure similar to an “Ω” shape. At last, some promising recommendations have been proposed, namely a theoretical predictive model which can describe the breakup mechanism of a liquid jet, the distribution characteristics and droplets size distribution of a liquid jet under a cavity combustion chamber, especially for enthalpy flows with complex wave structures.     

两种同类型胶片基础特性及检测应用比对

文摘针对如何在液体火箭发动机产品射线检测过程中,根据具体情况选择合适的射线胶片,达到既能保证射线检测图像质量又能提高检测效率减少检测成本的目的,本文通过对进口富士IX100型胶片和国产乐凯牌L7型胶片的特性和质量稳定性进行工艺对比试验。结果表明,L7型胶片本底灰雾度稍大于IX100型胶片,灵敏度逊于IX100型胶片,宽容度高于IX100型;但两者均属于GB/T19348.1—2003规定的T3范畴胶片,综合性能比较接近;L7型胶片适用于发动机上具有变截面的铝铸件、机加余量不大的钢铸件、钛铸件及大部分熔焊缝的射线检测。     

电动膨胀循环液氧甲烷变推力发动机动态特性研究

电动泵压式液体火箭发动机受到了广泛的关注，然而电池有限的输出功率和过于沉重的质量成为限制电动泵压式发动机发展的重要因素。为此本文提出了一种电机驱动燃料泵和涡轮驱动氧泵的电动膨胀循环液体火箭发动机方案，并着重研究了该型发动机的动态响应特性。首先给出了20 kN级电动膨胀循环发动机的技术指标和部组件参数，进一步基于AMESim平台建立了全系统动力学模型，验证了方案的可行性和部组件动力学模型的准确性，并深入研究了单点工况和调节工况的动态响应特性。结果表明，针对启动过程而言，涡轮泵调整时间较电动泵长，这降低了系统响应速度，但工况越高，系统响应速度越快；高工况启动时，甲烷在冷却通道内的剧烈相变和跨临界状态的不连续物性相互耦合易引发系统振荡；就调节过程而言，推力调节时普遍存在超调或凹坑现象，且系统在两相同工况之间调节时，正调响应速度快于负调，这也导致阶跃幅值相等条件下的系统调整时间随目标工况升高而缩短。