空气中微细电火花沉积铜合金工艺方法

提出了一种在空气中将工具电极丝黄铜材料沉积到工件上的新工艺方法。实现该方法的基本条件为:(1)工具电极接脉冲电源正极;(2)在空气中放电;(3)窄脉宽配合宽脉间。通过大量实验对微细电火花沉积加工的工艺规律进行了系统深入的研究,得出各主要工艺参数对沉积工艺效果的影响规律。最终以黄铜电极丝为工具电极,在高速钢工件表面上沉积出直径为0.19 mm、高度为7.35 mm的微小圆柱体。利用SEM、能谱分析和X射线衍射及显微硬度测试等方法对沉积物进行分析,得出该沉积物的组织结构、化学成分和硬度等方面的基本性质,为进一步研究三维沉积加工奠定了基础。     

空中受油管的绕流特性研究

空中加油是提高飞机航程、活动半径的重要方法。通过对四种固定受油管的数值模拟,从流动特性的改进方面说明了合适的截面及倾角会降低受油管绕流的压力脉动,进而使噪声降低。     

冲压空气涡轮性能的局部改进升力线算法

将现代螺旋桨的改进升力线算法应用于空气涡轮性能计算，结合冲压空气涡轮结构特性对叶片模化作了局部改进，对一个冲压空气涡轮模型作了计算，与实验结果和改进升力线法的对比表明，局部改进后的叶片环量和诱导速度分布合理，计算精度和宽度有明显改善，与实验符合较好。     

燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Suggestion for aircraft flying qualities requirements of a short-range air combat mission

Owing to the lack of a direct link with the operations in short-range air combat,conventional aircraft flying qualities criteria are inappropriate to guide the design of a task-tailored flight control law.By applying the mission-oriented flying qualities evaluation approach,various aircraft with different control law parameters are evaluated on a ground-based simulator.This paper compares the evaluation results with several conventional flying qualities criteria,and discusses the appropriate parameter combination to reflect the flying qualities requirements of short-range air combat,The comparison and analysis show that a short-range air combat mission requires a higher minimum short period mode natural frequency and a smaller maximum roll mode time constant,and allows a lower minimum pitch attitude bandwidth and a higher maximum short period mode damp ratio than those of conventional flying qualities criteria.Furthermore,a combination of the pitch attitude bandwidth,the pitch attitude magnitude at the bandwidth frequency,and the pitch attitude transfer function gain can define the flying qualities requirements of short-range air com bat.The new metric can successfully predict the flying quality levels of aircraft in a short-range air combat mission.     

Experimental analysis of the breakage of a liquid bridge under microgravity conditions

The experimental results obtained in experiment “STACO” made on board the Spacelab D-2 are re-visited, with image-analysis tools not then available. The configuration consisted of a liquid bridge between two solid supporting discs. An expected breakage occurred during the experiment. The recorded images are analysed and the measured behaviour compared with the results of a three dimensional model of the liquid dynamics, obtaining a much better fit than with linear models.     

某发动机调节器自动检测异常故障分析

针对某型发动机自动调节器自动检测异常的故障现象,对产生发动机自动调节器自动检测异常的原因进行了深入地研究分析,并提出了针对性的预防措施。     

波音737NG飞机大气数据探头自动加温功能测试的替代方法研究

根据波音AMM手册要求,在更换波音737NG飞机上的大气数据系统传感器后,需通过试车测试其自动加温功能。本文研究了波音737NG飞机大气数据系统探头自动加温的工作原理,并提出避免试车的解决方案。