锯齿尾缘叶片气动特性和绕流流场的数值研究

以基于NACA 0018翼型的锯齿尾缘仿生叶片为研究对象,采用大涡模拟的方法研究锯齿相对齿宽与相对齿高对锯齿尾缘叶片的气动特性和非定常绕流流场的影响规律和机制.研究表明,尾缘锯齿参数对叶片气动性能的影响是复杂的非线性过程,在一定来流攻角范围内能提高升阻比,但失速提前.如在9.4°~14.8°来流攻角范围内,不同相对齿宽系列叶片的升阻比高于原始叶片,升阻比与锯齿相对齿宽之间没有线性关系.研究还表明,锯齿尾缘能延迟边界层分离,加速尾迹的流动掺混和能量扩散,改变非定常涡结构和涡脱落频率.相对齿高的变化对非定常流动特性的影响更为显著.尾缘锯齿诱导的二次湍流射流和吸力面侧反向涡对改变了原始叶片的绕翼环量,进而影响锯齿尾缘叶片的气动特性和绕流流场特性.      

一种涡轮排气蜗壳的优化设计

为了改善涡轮排气蜗壳的排气效果,选取一种箱式蜗壳为原始计算模型,通过数值模拟研究了该排气蜗壳的气动性能,揭示了蜗壳内部流动损失的主要来源,在不改变其几何尺寸的前提下,提出了一种蜗壳的分流层改型设计,并与两种一般改型方式的效果作比较.数值计算结果表明:在设计工况下,分流层改型设计可使排气蜗壳的总压损失系数最多降低32.12%,静叶恢复系数最多提高48.73%,其效果好于扩压结构弧线改型,但弱于蜗壳壁面轮廓型线改型,在此基础上揭示了分流层设计改善蜗壳气动性能的机理.      

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

Numerical simulation of a rotary engine primary compressor impacted by bird

In order to examine the process of a rotary engine primary compressor impacted by bird, a finite element model of a bird impacted on plate is developed with the explicit code PAM-CRASH. The smooth particles hydrodynamic (SPH) method is used to simulate the bird because of the SPH method showing no signs of instability and correctly modeling the breaking-up of the bird into particles. Good agreement between the simulation results and experimental results indicates that the numerical method of bird strike used in the present paper is reasonable. Then a rotary engine primary compressor impacted by three different configurations bird named straight-ended cylinder bird, quadrangular bird, hemispherical-ended bird are investigated using the numerical simulation method. It is found that the whole process of bird strike sustained about 3.5 ms and the bird is slashed by blade during the strike. The geometry configuration of bird affected the displacement and von Mises stress of some blades severely, just because the breaking bird’s mass is affected by the bird’s configuration. In the event of bird striking on the site of"up"some blades may develop plastic deformation and it is very adverse for the safety work of the engine.     

锅炉分层给煤装置的机理及效果分析

影响锅炉热效率的因素有多种，其中最主要的有两点：一是煤的燃烧状况，一是炉膛的换热环境。本文从煤层结构对燃烧状况的影响这个角度分析了分层给煤装置的优点和不足，并提出了几点改进方法。     

Electromagnetic waves observed by Venus Express at periapsis: Detection and analysis techniques

The magnetometer on Venus Express was designed to be able to obtain 128 Hz samples of the magnetic field from two sensors in a gradiometer configuration. This mode is used around periapsis to determine whether the signals reported at low altitudes near 100 Hz, had the properties of electromagnetic waves generated by electric discharges in the Venus atmosphere. The lack of a magnetic cleanliness program and the shortness of the magnetometer boom make this a challenging measurement. Fortunately the signals are sufficiently strong that they can be easily resolved with rather straightforward analysis techniques.     

亚声速三角翼俯仰振动涡结构及升力特性研究

本文介绍在暂冲式三声速风洞中实现了非常流动的多片光蒸汽屏显示技术和测力技术，并用这两项技术研究了亚声速时７０°后掠三角翼模型仰振的非定常流动现象，探讨了由于三角翼模型俯振动产生的涡结构人向气动力特性之间的相关关系。     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

WL10型近红外反射式光电传感器的研制

依据光学电子学的相关原理，针对烟草行业自动生产过程中对传感器的需要，研制了ＷＬ１０型近红外反射光电传感器，并成功地应用于烟草行业的生产线上。     

增升状态下的全机位流数值模拟

研究了势流理论下的全机增升装置复杂外形气动力数值计算方法,该方法以低阶面元法为基础,具有计算量小、速度快的优点.复杂流动的粘性效应主要通过附面层粘性修正技术加以体现.采用该方法对某增升装置翼身组合体外形压力分布特性进行计算,并和风洞实验数据相比较,验证了方法的正确性和实用性.在此基础上对某型飞机真实复杂外形的压力分布特性进行了计算,为复杂外形飞行器增升装置的初步设计、方案选型与评估提供了非常理想的工程技术手段.