无人机单、双尾撑布局的结构效率研究

为了探讨在总体设计中单、双尾撑布局无人机的结构效率,本文采用工程梁方法对这一设计问题进行简化与建模,作为无人机设计时对结构因素的考虑。理论推导与实际算例结果均表明,双尾撑布局比单尾撑布局具有更高的结构效率,因而从结构刚度上能够解释很多无人机采用双尾撑布局的理由。最后,作者给出了3点结论。     

Determination of a suitable set of loss models for centrifugal compressor performance prediction

Performance prediction in preliminary design stages of several turbomachinery components is a critical task in order to bring the design processes of these devices to a successful conclusion.In this paper,a review and analysis of the major loss mechanisms and loss models,used to determine the efficiency of a single stage centrifugal compressor,and a subsequent examination to determine an appropriate loss correlation set for estimating the isentropic efficiency in preliminary design stages of centrifugal compressors,were developed.Several semi-empirical correlations,commonly used to predict the efficiency of centrifugal compressors,were implemented in FORTRAN code and then were compared with experimental results in order to establish a loss correlation set to determine,with good approximation,the isentropic efficiency of single stage compressor.The aim of this study is to provide a suitable loss correlation set for determining the isentropic efficiency of a single stage centrifugal compressor,because,with a large amount of loss mechanisms and correlations available in the literature,it is difficult to ascertain how many and which correlations to employ for the correct prediction of the efficiency in the preliminary stage design of a centrifugal compressor.As a result of this study,a set of correlations composed by nine loss mechanisms for single stage centrifugal compressors,conformed by a rotor and a diffuser,are specified.     

连续分离铝熔体中夹杂物的分析

通过分析高频磁场作用下熔体连续处理时夹杂的去除效率表明，熔体连续处理条件下的夹杂去除效率比熔体静止时的略低，而夹杂与熔体之间的密度差对电磁分离时的去除效率影响不大。提高去除效率的有效途径是增大磁感应强度或降低分离器管径，但减小管径的同时需要提高磁场频率，以保持α/δ的值在2附近才可以取得最佳的分离效果。     

毛细管放电型脉冲等离子体推力器输出特性分析

为了研究毛细管放电型脉冲等离子体推力器输出特性,借助电学诊断手段展开实验研究,获得了推力器典型放电波形,系统研究了不同毛细管内径和施加电压对等离子体等效阻抗、沉积能量效率的影响规律。利用微冲量测量台架,测试了不同参数下毛细管推力器输出元冲量,并通过计算获得了推力器比冲、总体效率的变化规律。实验结果表明,当毛细管内径不断增大时,能量沉积效率不断下降,元冲量下降,比冲降低。主电容电压增大时,放电能量不断增大,能量沉积效率降低,元冲量和单次等效烧蚀质量不断增大,但推力器比冲和总体效率均先增加并趋于稳定。当毛细管腔体长度为16mm,内径3mm,主电容2.5μF,充电电压为2kV时,输出元冲量350.79±7.50μN?s,比冲531s,总体效率可达18.3%。     

某涡轮级三维流场非定常数值研究

基于耦合Lantry-Menter转捩模型的SST(Shear stress transport)湍流模型,对某涡轮级在3个雷诺数工况下的全三维流场分别进行了定常、非定常数值模拟,目的在于对比分析两种计算方法所得结果之间的差异。计算结果表明,进口雷诺数为4×104时和5×105时,定常与非定常计算的涡轮级效率的差异较大,最大相差0.6个百分点,而当雷诺数为8×104时,两者差异很小;非定常计算能够较好的模拟叶尖泄漏涡的发展过程、低雷诺数下上游尾迹与下游转子叶片吸力面分离边界层干涉诱导卷起涡的形成、输运及其所导致的叶片吸力面表面压力大幅波动等非定常流动现象。最后,给出了转子出口截面上周向与径向的非定常压力脉动的分布,为基于Lighthill声类比方法的计算气动声学研究奠定了基础。     

高等职业教育发展品牌战略的思考

体现自身特色,强化品牌意识,实施品牌战略,抢占教育市场份额,是高职院校获得竞争优势的必由之路。通过教育品牌的重要性、办学理念和办学定位、特色教育及实施品牌战略等方面的论述,提出了塑造高职教育品牌的几个关键问题。     

微细旋转超声加工材料去除机理及试验

文摘分析旋转超声加工材料去除机理,建立材料去除效率模型,探讨工艺参数对加工效率的影响规律;对压电陶瓷、有机玻璃、玻璃钢、紫铜等多种材料,进行单一超声和旋转超声加工材料去除效率对比试验,研究旋转超声加工方式对加工过程稳定性及加工效率的影响。结果表明:旋转超声加工可在保持原超声加工精度基础上,显著提高材料加工效率,且对较难超声加工材料(如有机玻璃),旋转超声提高其加工效率的效果更为显著。     

系统可靠性设计

预计系统的可靠性，介绍综合累计法和失效率模型，给出三种可靠性分配方法，即等分配法，ＡＧＲＥＥ法、最小努力分配法。     

涡轮工作叶片表面气膜冷却效率的实验研究

在大尺寸低速线性叶栅风洞上进行实验,采用放大的叶片模型,测量了涡轮工作叶片表面不同位置单排气膜孔的气膜冷却效率,研究了孔排位置、吹风比及来流雷诺数的影响。试验叶片表面上开有8排气膜孔,其中吸力面2排,前缘区3排,压力面3排。实验的参数变化范围是:基于叶片弦长的来流雷诺数250000～450000,吹风比0 5～2 5。结果表明,由于气膜孔排位置的不同,其下游冷却效率受来流雷诺数及吹风比影响的变化趋势也有所不同,孔排位置一定时,冷却效率主要由吹风比决定。该实验结果对涡轮叶片型面气膜冷却的实际工程设计研究有重要意义。     

Power characteristics of a variable hydraulic transformer

The flow control of hydraulic transformers is a great challenge.To meet this challenge,a new kind of hydraulic transformer,variable hydraulic transformer(VHT),is proposed in this work.This paper focuses on the power characteristics of the newly proposed VHT,including instantaneous power,average power,power pulsation,and efficiency.In the analyses,the concepts of efficiency,input power,output power,starting angle,and ceasing angle are defined or redefined.To investigate the power characteristics,their models are derived by considering the governing factors such as the control angle of the swash plate and the structure of the port plate.This work highlights that the load flow can be adjusted by adjusting the control angle of the swash plate,and the power characteristics at the B-port produce a remarkable change.In addition,the VHT has a starting angle and a ceasing angle,and these two angles can be adjusted by the influencing factors.The results reveal that the power pulsation and the jump points of the instantaneous power are the primary causes of a less smooth work.Then,it is shown that the control angle of the port plate,the control angle of the swash plate,and the pressures at the ports are the three key elements for a stable operation.The results also reveal that the adjustment of the influencing factors can improve the efficiency.