基于模型的多电飞机能源优化特性仿真分析

多电飞机是一种用电能部分取代原来的液压能和气压能的飞机,其二次能源系统以电能为主。为实现多电飞机能源系统的优化设计,将飞机的发电、配电和用电集成在一个统一的系统内,实行发电、配电和用电的统一规划、统一管理和集中控制。为快速有效地分析多电飞机能源系统优化特性,本文采用基于模型的系统工程方法论,针对多电飞机能源优化仿真分析平台开展研究,提出了一种面向电气设备的多物理域模型建模方法,以实现机载系统的大规模集成仿真。并以飞控系统为对象,建立了多电飞机飞控系统和传统飞机飞控系统的能量利用、能量传送、能量变换设备等仿真模型,仿真分析了两种飞控系统的能源应用特性,为多电飞机能源系统的优化设计提供了有效支撑。     

Brazing diamond grits onto AA7075 aluminium alloy substrate with Ag–Cu–Ti filler alloy by laser heating

The brazing of diamond is a promising way to fabricate grinding wheels for efficient machining and precision grinding. This work investigated the feasibility of bonding diamond grits onto Aluminium Alloy 7075 (AA7075) substrate with a Ag–Cu–Ti filler alloy via laser fusion brazing. The interfacial microstructures and the strength of the brazed diamond joints were studied. The cross-section of the brazed diamond joint consists of a molten filler alloy layer, a molten pool, a heat effect zone, a columnar crystal zone and an equiaxed crystal zone. Within the interface of the filler alloy/substrate metal, microstructures observed possibly were Ag(s.s), Al(s.s), TixAl, Al2Cu and Mg intermetallic compounds. A layer of TiC with a thickness of about 30–50 nm was found at the bonding interface of the diamond/filler alloy. The averaged peak shear force of the brazed joints was found to be approximately 39.8 N. The abrasion grinding test indicated that the diamond/AA7075 brazed joint was adequate for grinding. However, the pulled-off of grit was found to be the primary failure of this type of brazed joint. This work broadened the brazing diamond technique and the range of applications of brazed diamond wheels for efficient grinding.     

Spin axis orientation of Ajisai determined from Graz 2 kHz SLR data

The Graz 2 kHz Satellite Laser Ranging (SLR) measurements allow determination of the spin axis orientation of the geodetic satellite Ajisai. The high repetition rate of the laser makes it possible to determine the epoch time when the laser is pointing directly between two corner cube reflector (CCR) rings of the satellite. Identification of many such events during a few (up to 3) consecutive passes allows to state the satellite orientation in the celestial coordinate system. Six years of 2 kHz SLR data (October 2003–October 2009) delivered 331 orientation values which clearly show precession of the axis along a cone centered at 14^h56^m2.8^s in right ascension and 88.512° in declination (J2000.0 celestial reference frame) and with an half-aperture angle θ of 1.405°. The spin axis precesses with a period of 117 days, which is equal to the period of the right ascension of the ascending node of Ajisai’s orbit. We present a model of the axis precession which allows prediction of the satellite orientation – necessary for the envisaged laser time transfer via Ajisai mirrors.     

Broglio Drag Balance for neutral thermosphere density measurement on UNICubeSAT

The nanosatellite UNICubeSAT is described, carrying a Broglio Drag Balance Instrument for neutral thermosphere density in situ measurements. The aim of the mission is to contribute to the development of accurate thermosphere models, achieving in situ, real time measurements of atmosphere density, that could be exploited for global atmosphere model validation and accurate short term (1–3 days) real time space weather forecasts. The satellite is inexpensive and swarms could be easily launched operating as a distributed sensor network to get simultaneous in situ local (not orbit averaged) measurements in multiple positions and orbit heights. The nanosatellite is based on the Cubesat standard architecture, weighing about 1 kg for 1-L volume. Atmospheric drag force is measured by the displacement of light plates exposed to the incoming particle flux seen by the spacecraft, applying the original three dimensional Broglio Drag Balance concept to a single nanosatellite axis. The instrument concept and its relation to the satellite bus is depicted, showing that many long term potential measurement error sources and biases can be removed in data processing if the spacecraft is spin stabilized. The expected accuracy in density measurements is 20%. The instrument cost is a fraction of that of accurate accelerometers. The onboard systems are based on commercial off the shelf components, in accordance with the short lifetime typical of aeronomy satellites.     

影响气冷式个体热防护装备致冷力的因素分析

个体气冷系统是一种致冷有效、穿着舒适的热防护装备,在设计和使用中 提高其致冷效率是至关重要的。从工程和生理上分析了影响个体气冷系统致冷力的多种 因素,包括供气温度、湿度、流量以及它们之间的相互关系、致冷面积、流量分配、隔热性 能等。得出了提高蒸发性和对流性两类通风服致冷力和舒适性的方法。为不同工况下合理设 计和选用气冷式个体热防护装备,使之具有更高的人机工效和更好的舒适性提供了参考和借 鉴作用。〖JP〗     

GPS L1频段上的系统内干扰的研究

为了在L1频段上有效发射多个高精度的导航信号,GPS全球导航卫星系统设计在同一中心频率上发射多个信号,各信号频谱严重重叠,因此内部干扰成为系统首要考虑问题。通过详细分析GPS L1频段上M码、L1C码、C/A码和P(Y)码的载噪比衰减值,发现除C/A码受到的干扰较严重外,其它三个信号受到的干扰较小,CDMA干扰是主要内部干扰源。分析结果表明,通过有效设计信号参数来减小CDMA干扰,使各信号功率谱主瓣相互错开,并合理设置信号接收功率,可以有效控制系统内干扰。
     

图解建模方法在提取沟壑密度中的分析研究

沟壑密度是反映地表破碎程度的重要因子,在土壤侵蚀、地貌演变等研究中有重要作用。对于沟壑密度的提取方法目前较为复杂,这主要由于在提取过程中所涉及到的因子数目众多,为进一步的空间分析研究设置了障碍。利用图解建模分析方法建立一套沟壑密度提取分析空间数据模型,对沟壑密度的快速提取提供了一套全新的解决方案。最后,以四川省数据为例,采用该分析方法提取出了四川省沟壑密度数据,为进一步研究四川省地形地貌特征奠定了基础。     

Complex Flow for Wing-in-ground Effect Craft with Power Augmented Ram Engine in Cruise

Power augmented ram (PAR) engine is a popular equipment to reduce the requirement of power for takeoff and improve aerodynamic performance. To provide detailed insight into the aerodynamic characteristics of wing-in-ground effect (WIG) craft with PAR engine, numerical simulations are carried out on WIG craft models in cruise. Simplified engine models are applied to the simulations. Two cruise modes for PAR engine are considered. The aerodynamic characteristics of the WIG craft and other features are studied. Comparisons with WIG craft model without PAR show that shutoff of PAR engine results in an increase in drag and less change in lift. Accordingly for the work of PAR engine, the air flow blown from the engine accelerates the flow around the upper surface and a high-speed attached flow near the trailing edge is recorded. With the schemed PAR flow, more suction force is realized and the flow features over the wing vary noticeably. It is also shown that the Coanda effect, provided with an attached flow, introduces an appropriate and practical flow mode for WIG craft with PAR engine in cruise. The results refresh our understanding on aerodynamic characteristics of WIG craft.     

脉冲激光推进的能量相似律理论研究

激光推进的能量相似律,指确定的激光能量有与之相对应的最佳喷管尺寸,使得冲量耦合系数最大且不变的规律。用大气高度参数、入射的激光能量、喷管几何参数构造了无量纲因子,建立了圆锥形喷管在单脉冲条件和一维球对称点聚焦情况下的能量相似律。结果表明:当锥角固定时,冲量和冲量耦合系数存在极大值,极大值对应的无量纲因子仅与气体比热比相关;当无量纲因子固定时,冲量随入射激光能量增加而单调增大,冲量耦合系数则与能量无关。本文的研究结论和规律性认识,对目前可实现和以后工程化放大的激光能量范围,均能给出可信可靠的喷管优化尺寸。     

光功率计测量不确定度评定

介绍了光纤功率标准装置的组成和工作原理,并对光功率计的测量不确定度进行了分析和评定。