含能工质激光烧蚀推进效率分析

为了分析在高能脉冲激光作用下,含能工质化学能对推进性能的影响,在实验的基础上,对固体含能工质激光烧蚀推进过程中的能量效率进行了初步分析。结果表明:含能工质自身化学能在激光推进中具有重要的作用;与火箭推进方式相比,固体含能材料激光烧蚀推进方式的能量利用效率更高。     

铝-锂合金的真空熔炼

 在ZG-25型中频感应真空炉中进行了铝-锂合金的熔炼与铸锭。真空度为66Pa。考察了普通石墨坩埚、氧化铝坩埚,以及氧化锌涂料、氮化硼涂料与铝-锂熔体的反应。抄到了在真空下控制铝-锂熔体中锂含量的方法。在不使用钛-硼细化剂的条件下,铸锭呈细小等轴晶组织,其成分均匀,夹杂物极少。真空熔炼可使合金中的氢、钾,钠等杂质含量显著地降低。     

Ti-24A1-17 Nb合金的激光焊接

研究了Ti-24Al-17Nb合金的激光焊接及其接头的力学性能.研究结果表明,连续激光氦气双面保护可以获得保护效果可靠、无缺陷、成型良好的焊接接头.焊接热输入增大不利于接头的纵向弯曲塑性,而接头的横向拉伸强度与母材基本相同,塑性可以接近母材的塑性,达到14%～17%.     

高能CO2激光腔镜高反介质薄膜的传输特性

为了获得适用于高能CO2激光器的高抗破坏阈值高反薄膜,以10.6μm高反膜ZnSe/YbF3,PbTe/BaF2膜系为例,数值模拟了激光在高反介质膜中的传输的场特性;给出了激光在多层介质膜中的场强分布、温度场分布及热应力分布。结果表明硅镜基体上的PbTe/BaF2膜系所需膜层厚度小、膜层数少,反射率可高达99.98%。     

空气中微细电火花沉积铜合金工艺方法

提出了一种在空气中将工具电极丝黄铜材料沉积到工件上的新工艺方法。实现该方法的基本条件为:(1)工具电极接脉冲电源正极;(2)在空气中放电;(3)窄脉宽配合宽脉间。通过大量实验对微细电火花沉积加工的工艺规律进行了系统深入的研究,得出各主要工艺参数对沉积工艺效果的影响规律。最终以黄铜电极丝为工具电极,在高速钢工件表面上沉积出直径为0.19 mm、高度为7.35 mm的微小圆柱体。利用SEM、能谱分析和X射线衍射及显微硬度测试等方法对沉积物进行分析,得出该沉积物的组织结构、化学成分和硬度等方面的基本性质,为进一步研究三维沉积加工奠定了基础。     

彩色三维激光快速成型技术的研究

目前逆向工程采用线结构激光和一个彩色面阵CCD摄像机构成三维彩色扫描系统,彩色CCD摄像机分两次对被测物体成像,首先摄取物体的彩色图片,然后加用滤光片再摄取激光光平面上的三维信息.最后将两次获取的信息重叠,便可得到三维彩色信息.提出了激光光平面方程式三维测量方法,建立了相应的数学模型.研制成一套适用于彩色逆向工程流程,并进行了实验研究,给出了实验结果.     

Microstructure,porosity and mechanical properties of selective laser melted AlSi10Mg

Finite element modeling (FEM), microscopy, X-ray computed tomography (CT) and mechanical property tests were used to study the microstructure, porosity and mechanical properties of an AlSi10Mg alloy produced by selective laser melting (SLM). The simulation of the melt pool and thermal history under different energy densities produced an optimized result with an energy density of 44.5 J·mm⁻³. The high cooling rate during the SLM process significantly refined the previous α-Al dendrites. The growth direction of the network-like Al-Si eutectic structure at different orientations confirmed the anisotropic nature of the microstructure. Furthermore, the microhardness, tensile testing and fracture analysis results proved that there were no obvious distinctions in the strength between the transverse and longitudinal directions, and that the ductility was anisotropic, possibly due to the shape and distribution of the pores. The pores measured by X-ray CT at different energy densities confirmed that the sphericity of the pores was inversely related to pores volumes. With optimized processing conditions, the porosity of the selective laser melted sample decreased leading to the improved fabricated fuel system component via SLM.     

某型航空活塞发动机曲轴喷油螺钉的维修工艺研究

喷油螺钉是某型航空活塞式发动机曲轴组合中的重要零件，单纯采用超声波清洗难以清除该零件内部积炭。结合生产实践对工艺进行改良，使该零件修理后的抽检合格率由20%提升至70%，缩短了发动机的翻修时间，节约了维修成本。     

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

A shortcut to marking 3D target curves on curved surface via a galvanometric laser scanner

Marking arbitrary three-dimensional(3D) target curves on given objects with curved surface is required in many industrial fields, such as fabric prepreg placement in composite material part fabrication, product assembly, surface painting for decoration, etc. A shortcut to the solution of this intractable problem is proposed by utilizing a galvanometric laser scanner(GLS) with the aid of a camera. Without using the existing tedious GLS calibration procedures,the proposed method directly establishes a mapping between the 3D coordinates of the laser spots on the object surface and the control voltages of the scanner. A single-hidden layer feedforward neural network(SLFN) is employed to model the mapping. By projecting a dense grid of laser spots on the object to be marked and simultaneously taking only one image, the SLFN model is trained in minutes via a linear solving mechanism. Experiments demonstrate that the trained SLFN model has a good generalization performance for marking 3D target curves. The 3D laser marking errors on experimental objects are less than 0.5 mm. The proposed method is especially suitable for on-site use and can be conveniently extended to multiple GLSs for marking large complex objects.