用电离层特性参量提取等效风场信息

导出了利用中低纬电离层特性参量获取电离层F层峰区高度上等效风场（包含电场和风场信息在内）的基本方程，并尝试用该方法从电离层特性参量（峰高和临频）提取等效风场信息，利用武汉站DGS-256电离层数字测高仪数据及由美国Massachusetts Lowell大学最新版的剖面反演程序换算得到F层峰高，获得了武汉地区夏季至日点附近，冬季至日点附近，冬季地磁特别宁静的九天和冬季平均等效风场的初步特征，并利用Fejer经验电场模式计算冬季电场引起的垂直漂移，估计电场和风场对武汉地区的垂直等效风场的贡献大小，结果表明：等效风场呈现出白天与夜晚幅度和方向的差异。至日点附近冬季与夏季白天的幅度差异以及明显的凌晨凹陷现象；平均情况下，垂直等效风场幅度和方向的变化主要是由中性风引起，受电场的影响不大。     

雷暴云准静电场和夜间低电离层的电离

用点电荷模型计算雷暴云突然放电后形成的准静电后形成的准静电场随高度的分布，以E/N（E的电场大小，N为大气密度）为输入参量，在一定条件下，对Boltzmann方程数值求解，计算电离层电子数密度的扰动。计算结果表明，在约70-90km之间，在约放电后的10ms内，准静电场大于中性大气的击穿电场，将引起大气的雪崩电离，从而引起夜间低电离层电子密度的显著增加，但这种电子密度的增加是暂的，在很短的时期内就恢复到平静时的水平，恢复时间随高度的变化而不同。     

彩色三维激光快速成型技术的研究

目前逆向工程采用线结构激光和一个彩色面阵CCD摄像机构成三维彩色扫描系统,彩色CCD摄像机分两次对被测物体成像,首先摄取物体的彩色图片,然后加用滤光片再摄取激光光平面上的三维信息.最后将两次获取的信息重叠,便可得到三维彩色信息.提出了激光光平面方程式三维测量方法,建立了相应的数学模型.研制成一套适用于彩色逆向工程流程,并进行了实验研究,给出了实验结果.     

The characteristics of sharp (small-scale) boundaries of solar wind plasma and magnetic field structures

We investigate properties of large (>20%) and sharp (<10 min) solar wind ion flux changes using INTERBALL-1 and WIND plasma and magnetic field measurements from 1996 to 1999. These ion flux changes are the boundaries of small-scale and middle-scale solar wind structures. We describe the behavior of the solar wind velocity, temperature and interplanetary magnetic field (IMF) during these sudden flux changes. Many of the largest ion flux changes occur during periods when the solar wind velocity is nearly constant, so these are mainly plasma density changes. The IMF magnitude and direction changes at these events can be either large or small. For about 55% of the ion flux changes, the sum of the thermal and magnetic pressure are in balance across the boundary. In many of the other cases, the thermal pressure change is significantly more than the magnetic pressure change. We also attempted to classify the types of discontinuities observed.     

一般硬化材料弹塑性旋转盘的变分解法

首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;再在体积不变条件下用弹性位移场的已知模态和一待定幅值构成弹塑性位移场;最后用势能原理确定该幅值而得到封闭解。     

研究用现场数据估计系统可靠性参数置信区间

研究用元部件现场信息估计系统可靠性参数,如系统可靠度、可靠寿命等区间估计问题。文中提出了一种新的估计方法——替换百分点法,并运用Monte Carlo数字仿真对估计的置信度和精度进行了分析,研究结果表明此方法具有工程应用价值。     

参量型空气折射率传感系统

本系统分别利用传感器测出空气的温度、气压和湿度三个参量,把测量值用一个通用于不同机型的接口电路连接到微机进行数据处理并计算出空气折射率值。文中叙述了传感器及其检测电路的设计原理,给出了检测和接口电路框图、计算公式和程序流程图。整个系统已通过联机调试和初步的对比试验。     

基于SPCE061A数字语音温度控制系统的设计

以凌阳SPCE061A单片机为控制核心,设计并制作了一款具有温度设定灵活、数字显示及语言播报功能的水温控制器,通过PID控制算法产生脉宽调制波,提高了控制精度。实践表明:该水温控制器达到了设计要求,有一定的实用开发价值。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

线性摩擦焊设备的振动测量和分析

针对线性摩擦焊设备焊接误差较大的问题，采用参数记录系统和加速度传感器测量了设备多个部位的振动幅度，并设计了高刚度顶锻滑台，为线性摩擦焊设备优化结构设计、减小振动以提高焊接精度提供了参考。