行星际空间质子引起介质深层充电的GEANT4模拟研究

高通量的空间质子是导致行星际航天器深层充电的主要原因,基于辐射诱导电导率模 型（RIC）和粒子输运模拟工具GEANT4对介质材料在质子辐照条件下的深层充电问题进行了 预估。利用GEANT4-RIC充电计算方法,首先计算出10MeV质子在Kapton和Teflon中的注量和 剂量沉积曲线,进而根据电流连续性方程、泊松方程和电荷俘获方程组成的辐射诱导电导率 模型（RIC）求解出介质内电荷和电场分布,与介质击穿电场阈值对比作为其是否发生放电 的依据。模拟结果证实了对10MeV质子,在质子注量为3×10 12 ／cm 2时Kapton会发 生放电,而Teflon则不会发生放电的一般性试验结论。验证了GEANT4-RIC方法用于行星际航 天器介质材料质子充放电评价的可行性,为此类问题的解决奠定了基础。
     

GH3600精细薄壁管内壁折叠缺陷分析

为了提高GH3600精细薄壁管质量,利用内窥镜和扫描电镜,对管材内壁折叠缺陷进行了解剖观察,测量了折叠的深度,并分析了折叠缺陷产生的原因和它对后续成型的影响,提出了避免折叠缺陷的工艺改进措施。     

熔模精铸件凝固过程温度场的数值模拟

根据熔模精密铸造过程的传热特点,通过对铸型/环境边界及冒口/环境边界进行自然对流和辐射传热处理,改进了原有数值模拟系统,实现了对熔模铸造凝固过程温度场的数值模拟.对采用4种不同铸造工艺方案的阀体铸件凝固过程进行了数值模拟及缺陷预测,获得了与试验相一致的模拟结果.根据数值模拟结果,确定了进行批生产的铸造工艺方案.     

航空发动机神经网络内模控制

基于神经网络内模控制理论研究了神经网络内模控制方法在航空发动机控制系统中的应用,建立了基于Elman网络的航空发动机多变量内模控制系统。采用Elman网络建立发动机内模型和内模控制器,详细介绍了建模、控制的算法及其实现过程。取部分飞行条件下的数据作为学习样本,采用动态BP算法对神经网络权值进行调整,并在飞行包线内其它工作点对整个控制系统进行了仿真。结果表明,使用神经网络建立的航空发动机内模控制系统具有良好的控制品质和较强的自适应能力。      

含中介轴承内圈局部缺陷的双转子系统的组合共振特性

针对航空发动机双转子系统建立简化的动力学模型,在考虑中介轴承非线性Hertz接触力和径向游隙等非线性因素的情况下,将中介轴承内圈局部缺陷模拟成倒置的等腰梯形凹槽,利用4阶Runge-Kutta法进行数值计算,得到系统的分岔图,并着重分析分岔区域的组合共振特性,结果表明：相较于无故障系统,该系统在分岔图上出现三个新的分岔区域,前两个分岔区域是由内圈故障特征频率与高低压转子的转频形成的组合频率诱发的组合共振引起的,第三个是由内圈故障特征频率诱发共振引起的,在分岔区域内,系统运动的周期性的变化规律表现为从近似单周期运动到概周期运动再到近似单周期运动。     

三维烧蚀内部热响应数值计算研究

对热解型碳化复合材料三维烧蚀内部热响应数值计算关键技术进行了研究。采用碳化层—热解面—原始材料层模型,将热解气体与碳化层之间的对流换热处理为源项,通过有限元法建立移动边界条件下温度场求解方程组,采用Gauss Seidel迭代法计算热解气体质量流量和温度场。同时,研究和分析了三维烧蚀移动边界处理方法以及动网格生成方法。由于每个时间步都需要网格重划,烧蚀热防护数值计算对存储效率和计算效率要求较高,本文研究了内部热响应计算中影响存储效率和计算效率的主要因素,并提出了相应的压缩存储方案和求解方案。计算结果表明,移动边界处理方法准确合理;存储方案的存储效率较高;保持刚度矩阵和形函数矩阵正定对称性可以加快温度场计算的收敛速度。     

CFRP曲面铣削力及加工缺陷研究

碳纤维增强复合材料(Carbon fiber reinforced polymer,CFRP)曲面结构不断变化的工件倾角使得在加工过程中易产生分层、毛刺等缺陷。为研究工件倾角对CFRP曲面结构可加工性的影响规律,采用金刚石涂层铣刀对不同倾角下CFRP叠层平板结构进行顺铣加工试验,对不同坐标系下的铣削力和加工侧面、表面缺陷进行了研究。研究结果表明,随工件倾角的增大,水平方向上每齿所切材料平均厚度与截面积均减小,等效轴向切深逐渐增大,但是每齿去除材料体积保持不变。机床坐标系下的铣削力几乎不随工件倾角的变化而变化。而在工件坐标系下,铣削力沿工件厚度方向逐渐增大,沿工件长度方向逐渐减小。同时随着工件倾角的增大,侧面表层分层缺陷不断加重,纤维束发生弯曲,裂纹沿纤维方向逐渐扩展至表层内部,加工表面遭受破坏铺层数量也同样增加。     

基于机器视觉与UMAC的自动铺丝成型构件缺陷检测闭环控制系统

为保证自动铺丝成型构件的性能,实现对成型构件表面质量的高效检测,本文基于机器视觉检测技术,自行研发自动铺丝成型构件表面缺陷检测闭环控制系统,使自动铺丝过程中预浸纱之间的间隙或重叠在允许范围内,从而保证铺丝精度。研究主要分为三个部分:铺丝成型构件表面图像提取与缺陷检测,检测数据传输,运动轴反馈控制,实现在自动铺丝过程中对成型构件表面缺陷检测实时闭环控制。针对电荷耦合相机采集到的预浸纱图像存在运动模糊和信噪比低等问题,将图像预处理划分为图像复原和降噪两大功能,根据不同类型的噪声采用对应滤波法进行降噪处理,提高了图像的信噪比,为后续检测提供高质量图像;预浸纱缺陷主要由其边缘直线这一几何特征进行表征,因此通过对预浸纱边缘检测实现缺陷识别;利用工控机向图像采集控制器发送命令实现图像采集,同时通过工控机与运动控制器之间信息流和数据流的交换实现检测数据的传输。探讨模糊控制理论用于闭环控制的研究,在反模糊化环节后面,加入自适应参数调节,以适应加工过程的突变,并成功地应用到自动铺丝缺陷检测闭环控制系统中,提高了伺服跟踪精度和跟踪实时性,从而提高铺丝精度。     

A review of recent studies on rotating internal cooling for gas turbine blades

Gas turbines have been used extensively for aircraft and marine propulsions as well as land-based power generation because of their high thermal efficiency and large power to weight ratios. To further increase the thermal efficiency, numerous prior researches on gas turbine blade internal cooling have been intensively carried out, majorly under stationary conditions. However, the stationary studies neglect the effects of Coriolis and buoyancy forces, which should change the velocity, turbulence and temperature distribution under rotating conditions. To elucidate the rotational effects on gas turbine internal cooling, the extensive results collected from recent investigations are discussed, which include the rotation and buoyancy effects on the rib turbulated cooling, pin fin cooling, jet impingement cooling, dimple/protrusion cooling, latticework cooling as well as swirl cooling. The rotational effects on the friction factors and the most employed experimental and numerical methods are also presented. Moreover, recommendations for future research are outlined. Therefore, this review article provides extensive literature information for the design of the next-generation high-efficiency internal cooling for rotating turbine blades.     

Nonlinear resonance characteristics of a dual-rotor system with a local defect on the inner ring of the inter-shaft bearing

In this paper, the nonlinear resonance characteristics of a dual-rotor system are investigated with the consideration of a local defect on the inter-shaft bearing of the system. A simplified model of the dual-rotor system is proposed by considering that there is a local defect on the inner ring of inter-shaft bearing. The local defect is modelled as an inverted isosceles trapezoidal groove, which can make great influence on the inter-shaft bearing force due to the change of radial clearance of the inter-shaft bearing. The motion equations of the dual-rotor system are formulated by using the Lagrange equation. The Runge-Kutta method is employed to solve the motion equation. The amplitude-frequency response curve of the dual-rotor system is obtained, the abnormal resonance characteristics are analyzed. In addition, the influence of defect parameters, rotors and support parameters and inter-shaft bearing parameters on the amplitude-frequency characteristics of the system are discussed. The results show that there are two main resonance peaks and four abnormal resonance peaks on the amplitude-frequency response curve of the dual-rotor with a local defect on the inner ring of the inter-shaft bearing. Through analyzing the vibration response of the abnormal resonance peaks, it is found that the first two abnormal resonances are caused by the combined resonance, which are related to the inner ring fault and the rotational speed of high or low pressure rotors, and the last two resonances are caused by the induced resonance of the inner ring fault. At the same time, when the parameters of defect, rotors and support and inter-shaft bearing change, the resonance of the system also shows the corresponding change law.