Investigation on the interface damage in drilling low-stiffness CFRP/Ti stacks

Carbon fiber reinforced plastic and titanium alloy (CFRP/Ti) stacks have been widely used as aerospace structures because of their excellent combination of physical properties. Interface damage caused by interface gaps, significantly different from that of metal/metal stacks, is a common problem in the through-hole drilling of CFRP/Ti stacks with low stiffness. In this study, a force–deformation coupling model was developed to further examine the formation mechanism and the control method of interface damage. Firstly, the coupling model was built considering the interaction between the thrust force and the deformation. To solve this model, a numerical method was proposed in which specific cutting coefficients were calibrated using only the thrust force of rigid stacks. Secondly, drilling experiments were performed with different feed rates and bending stiffness. Experimental results indicate that interface damage mainly includes interlayer chips and surface damage of CFRP layers. The surface damage, which is irreparable, is caused by the rotary extension of metal chips along the interlayer gap. Thirdly, variations of the interface gap were calculated with the coupling model that had been verified by measured thrust forces. The damage area was found to have a linear dependence relation with the interlayer gap. However, in conditions of large gap sizes, the interface damage areas increased with the interlayer gap at high feed rates, while decreasing slightly at low feed rates. This phenomenon was satisfactorily explained by the presented model. Finally, a method was proposed to determine the appropriate pressure exceeding which no interlayer damage will occur. Additional drilling experiments proved the method effective. This study leads to further understanding of the forming mechanism of interlayer damage and of selecting appropriate parameters in drilling low-stiffness composite/metal stacks.     

运载火箭贮箱壁板化铣旋转设备的设计

根据运载火箭贮箱壁板精密化学铣切减重的技术要求,分析了设计技术难点,通过确定制动电机,计算传动比、线速度,释放扭矩和消除两侧齿轮间隙等,研制了一套专用定位倍式化学铣切旋转设备。采用倍式转动化学铣切,减少了传动间隙,提高了转动扭矩和使用寿命加工精度,确保运载火箭贮箱壁板的精密化学铣切的要求。     

展成电解加工整体叶轮扭曲叶片中的间隙分析

叙述了展成电解加工整体叶轮扭曲叶片中间隙的计算方法,并讨论了工件和阴极各运动速度对间隙的影响。     

论家户特征对城乡收入差距的影响

自改革开放以来，我国经济高速增长，与此同时，我国城乡收入差距在总体上呈现逐步扩大的趋势。在经济发展过程中，城市与农村家户特征如就业人数、文化程度、行业类别、年龄结构等存在着较大的差异，这些差异是影响城乡收入差距的重要因素。     

配合间隙对涡轮叶片榫头/榫槽接触的影响

采用率相关晶体塑性滑移理论模型,考虑镍基单晶的晶体取向和涡轮盘/片配合间隙的影响,针对涡轮叶片榫头/榫槽的复杂接触状况,研究了温度梯度载荷和离心载荷作用下三种取向的接触应力和低周疲劳损伤。结果表明:当榫头/榫槽的配合间隙小于3.7μm时,榫头/榫槽的接触应力随间隙值突变比较明显;而间隙值大于5.4μm时影响较小。接触应力和低周疲劳寿命对第一齿间隙值比较敏感,随间隙值的波动变化范围较大;第二齿的间隙对接触应力影响也较大,但对疲劳寿命的影响只在较小间隙值下较为明显。晶体取向对榫头/榫槽接触低周疲劳寿命有比较显著的影响,表现出明显的疲劳性能各向异性。     

PW2037发动机VSV系统非典型故障分析

现代民用涡扇发动机普遍采用VSV系统提高发动机的喘振裕度和性能,该系统的常见故障主要集中在控制系统部件及相关线路上,本文介绍了由于VSV系统同步环滑块和HPC机匣间隙原因导致的非典型VSV系统故障,对VSV系统间隙性重复故障的排除具有一定参考作用。     

GPS-only gravity field recovery with GOCE,CHAMP, and GRACE

Gravity missions such as the Gravity field and steady-state Ocean Circulation Explorer (GOCE) are equipped with onboard Global Positioning System (GPS) receivers for precise orbit determination (POD), instrument time-tagging, and the extraction of the long wavelength part of the Earth’s gravity field. The very low orbital altitude of the GOCE satellite and the availability of dense 1 s GPS tracking data are ideal characteristics to exploit the contribution of GPS high-low Satellite-to-Satellite Tracking (hl-SST) to gravity field determination. We present gravity field solutions based on about 8 months of GOCE GPS hl-SST data from 2009 and compare the results with those obtained from the CHAllenging Minisatellite Payload (CHAMP) and Gravity Recovery And Climate Experiment (GRACE) missions. The very low orbital altitude of GOCE significantly improves gravity field recovery from GPS hl-SST data above degree 20, but not for the degrees below 20, where the quality of the spherical harmonic coefficients remains essentially unchanged. Despite the limited time span of GOCE data used, the gravity field of the Earth can be resolved up to about degree 115 using GPS data only. Empirically determined phase center variations (PCVs) of the GOCE onboard GPS helix antenna are, however, mandatory to achieve this performance.     

验证板反射冲击波对固体推进剂冲击起爆影响的实验研究

根据隔板实验确定固体推进剂临界爆轰压力时,往往假定被测推进剂药柱是在隔板界面附近起爆,忽视了验证板界面会反射强冲击波的特性,这些假定并没有实验进行验证和事实依据。因此,文中对隔板实验中验证板反射的冲击波对冲击起爆影响进行了实验研究,设计了对比验证实验,对比实验结果清楚地消除了验证板反射冲击波影响的不确定性,为以隔板界面入射冲击波压力作为被测推进剂药柱临界爆轰压力提供了可靠依据。     

三种不同面容比模拟积水溶液环境中300M钢的腐蚀行为

基于飞机结构材料300M钢在海洋高湿环境中缝隙部位积水导致的腐蚀损伤问题,研究了300M钢在3种不同面容比模拟积水溶液环境中的腐蚀行为,借助Tafel极化曲线和电化学交流阻抗谱实验探讨了影响腐蚀速率的主要原因。在模拟积水环境中,分析了腐蚀失重、失重速率、损伤度以及腐蚀过程中腐蚀溶液溶解氧浓度、pH值与不同面容比（2、5、20 mL/cm²）之间的关系。结果表明：随材料腐蚀时间的延长,腐蚀溶液中的溶解氧浓度降低,pH值上升,而且随面容比的增大,材料的腐蚀失重增加,腐蚀失重速率也增大。Tafel极化曲线和电化学交流阻抗谱结果表明,不同pH值下300M钢耐蚀性的差别导致了不同面容比环境下腐蚀损伤的差异,3种面容比模拟积水环境中腐蚀速率大小为V₂₀>V₅>V₂。     

周向弹簧力分布对圆周密封装置密封性能的影响

为了研究周向弹簧力分布形式对密封装置密封性能的影响,针对周向弹簧建立力学模型,分析周向弹簧力不均匀分布形式产生的原因,并对其不均匀分布的临界范围进行预测分析,建立泄漏预测模型对密封结构的密封性能进行研究。首先对密封装置主要结构进行受力分析,研究周向弹簧不均匀加载对密封结构变形的影响,再结合ANSYS软件对圆周密封装置主要部件进行结构-热耦合仿真计算,进而通过仿真分析验证理论分析的合理性。仿真结果表明：不均匀周向弹簧力产生的附加力矩使得密封环翘曲变形,主密封面径向接触间隙最大位置出现在密封环的接头区域;相比弹簧力分布均匀条件,当弹簧力分布形式的不均匀程度处于临界范围内时,接触间隙增加了24.52%,气体泄漏量增加了7.99%;当弹簧力分布形式的不均匀程度处于临界范围外时,接触间隙值呈倍数增加,气体泄漏量增加一个数量级。综上,周向弹簧力不均匀分布导致主密封面接触间隙值增加、密封结构气体泄漏量增加、密封装置密封性能下降。周向弹簧力的不均匀分布对密封装置的密封性能有较为严重的影响,在实际工程应用中应尽可能保证周向弹簧的不均匀分布程度处于临界范围内,避免由于弹簧卡滞使得密封结构密封性能下降。