Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

Case study of inclined sporadic E layers in the Earth’s ionosphere observed by CHAMP/GPS radio occultations: Coupling between the tilted plasma layers and internal waves

We have used the radio occultation (RO) satellite data CHAMP/GPS (Challenging Minisatellite Payload/Global Positioning System) for studying the ionosphere of the Earth. A method for deriving the parameters of ionospheric structures is based upon an analysis of the RO signal variations in the phase path and intensity. This method allows one to estimate the spatial displacement of a plasma layer with respect to the ray perigee, and to determine the layer inclination and height correction values. In this paper, we focus on the case study of inclined sporadic E (E_s) layers in the high-latitude ionosphere based on available CHAMP RO data. Assuming that the internal gravity waves (IGWs) with the phase-fronts parallel to the ionization layer surfaces are responsible for the tilt angles of sporadic plasma layers, we have developed a new technique for determining the parameters of IGWs linked with the inclined E_s structures. A small-scale internal wave may be modulating initially horizontal E_s layer in height and causing a direction of the plasma density gradient to be rotated and aligned with that of the wave propagation vector k. The results of determination of the intrinsic wave frequency and period, vertical and horizontal wavelengths, intrinsic vertical and horizontal phase speeds, and other characteristics of IGWs under study are presented and discussed.     

机匣沟槽对微型轴流涡轮叶尖泄漏流动的影响

本文通过对某微型涡喷发动机的单级轴流式涡轮进行机匣设计,采用剪切应力输运(SST)模型求解定常黏性雷诺平均Navier-Stokes方程,研究了不同机匣沟槽结构对其叶尖泄漏流动的影响。计算结果说明：当全机匣沟槽结构的叶顶浸入沟槽即d/c＞1.0时,封严效果较好;相较于全机匣沟槽结构,后开式机匣沟槽结构的封严效果更好, 随着沟槽前缘间隙的增大,封严效果减弱;沟槽深度a/c=1时,封严效果最佳,即泄漏流明显减弱,同时效率减小量较小。     

径向磁气组合轴承系统的动态性能

为探究磁轴承失效时能否减轻转子跌落带来的损害,将人字槽径向动压气体轴承引入磁轴承转子系统,研究磁气组合轴承对系统动态性能的影响和动压气体轴承的支承特性。采用有限差分法和小扰动法求解气膜厚度方程和雷诺方程,研究动压气体轴承的静动态特性。对磁轴承电磁力进行了分析,采用磁轴承不完全微分PID（比例-积分-微分）控制策略,对系统进行了理论模态分析和试验模态分析,完成了系统高速旋转试验,测试了动压气体轴承在不同偏心率和转速下的承载力。结果表明,引入动压气体轴承可提高系统的动态性能,在磁轴承失效造成高速转子跌落瞬间,偏心率趋近于1,两个径向动压气体轴承能够产生较大承载力,减轻转子跌落造成的损害。      

倾斜微槽道热管中纳米流体的应用

为了研究热管倾斜角度和压力对热管蒸发段、冷凝段传热系数以及最大换热功率的影响,对使用水基CuO纳米流体为工质的倾斜微槽道热管强化换热特性进行实验研究.实验装置主要由带角度调节功能的微槽道热管和加热、冷却系统组成.实验结果发现,用水基纳米流体替代去离子水为工质时,热管整体换热特性得到明显增强,蒸发段、冷凝段传热系数以及最大功率都能大幅度提高,总热阻明显降低.倾斜水热管的蒸发段和冷凝段传热系数比水平水热管的有大幅提高,但最大功率变化不大.而倾斜纳米流体热管不但蒸发段和冷凝段传热系数比水平纳米流体热管有大幅提高,而且最大功率更有接近一倍的增加.对水和纳米流体两种工质,对应于最佳换热特性的倾斜角都是75°.因此,纳米流体对倾斜热管有良好的应用前景.      

间隙流触发压气机内部流动失稳机制及周向槽扩稳机理

利用高频响动态压力传感器对某低速轴流压气机转子的失速先兆和顶部流场进行了详细的测试,探明该压气机内部存在与叶顶间隙泄漏流相关的突发型失速先兆,对压气机转子内部流场进行了单通道定常和非定常数值模拟,详细分析了压气机内部流动失稳过程中顶部流场结构的变化,揭示顶部间隙泄漏流触发轴流压气机内部流动失稳机理.在此基础上,利用周向槽处理机匣结构对顶部间隙泄漏流进行控制,并探讨了周向槽处理机匣结构提高压气机稳定工作裕度机理.      

整体构件周向叶片电解加工流场设计及实验

针对整体构件周向叶片的特点与加工难点,设计了带有内置绝缘腔的电解套型加工工具阴极,建立了两种进液方式的流场三维模型,采用有限元法对两种进液方式的流场进行仿真计算。计算结果表明由绝缘腔的叶盆叶背两侧进液并对出液口进行优化的流场方式较好,电解液流速较高且流场较均匀。使用根据有限元仿真结果设计的阴极开展实验,结果表明实验与流场仿真结果相符,采用优化流场模型的加工过程流场稳定,加工效率较高。     

测点布局对航空发动机总压畸变指数的影响

为了阐明测点布局对航空发动机进气总压畸变测试结果的影响，利用旋转总压测量耙对5种畸变流场的稳态和动态总 压畸变成分进行了测试，计算了旋转总压测量耙位于不同位置时畸变流场的稳态周向总压畸变指数和动态总压畸变指数，分析了 不同测点布局下总压畸变指数计算结果的偏差。结果表明：测量耙/测点与畸变流场的相对周向位置对总压畸变指数计算结果的 准确性至关重要，对于所分析的5种畸变流场，增加测量耙/测点周向数目并不能使总压畸变指数计算结果的偏差单调减小，但可 降低其对测量耙/测点周向位置的敏感度。基于畸变区域周向分布设计稳态总压畸变测量耙的周向位置，组合使用不同相对半径 处测点对动态总压畸变进行监测，可提高总压畸变指数计算结果的准确性。     

互相关函数在窄槽对中上的应用研究

不等距的窄槽载正加工是机械加工的难题之一。文中采用了电涡流传感器来采集窄槽的位置信号，利用信号边沿部分对称的特点，采用了“倒序列相关”的方法 用倒序信号与原信号进行互相关分析，充分利用了信号的全过程，滤除了信号中的随机成分，精确地求得窄槽的中心位置。试验的结果与理论研究基本相符，表明此方法具有实用价值。