Extrinsic calibration of a laser displacement sensor in a non-contact coordinate measuring machine

In order to implement 3D scanning of those complicated parts such as blades in the aviation field,a non-contact optical measuring system is established in the paper,which integrates a laser displacement sensor,a probe head,the frame of a coordinate measuring machine (CMM),etc.As the output of the laser sensor directly obtained possesses the 1D length of the laser beam,it needs to determine the unit direction vector of the laser beam denoted as (l,m,n) by calibration so as to convert the 1D values into 3D coordinates of target points.Therefore,an extrinsic calibration method based on a standard sphere is proposed to accomplish this task in the paper.During the calibration procedure,the laser sensor moves along with the motion of the CMM and gathers the required data on the spherical surface.Then,both the output of the laser sensor and the grating readings of the CMM are substituted into the constraint equation of the spherical surface,in which an over-determined nonlinear equation group containing unknown parameters is established.For the purpose of solving the equation group,a method based on non-linear least squares optimization is put forward.Finally,the system after calibration is utilized to measure the diameter of a metallic sphere 10 times from different orientations to verify the calibration accuracy.In the experiment,the errors between the measured results and the true values are all smaller than 0.03 mm,which manifests the validity and practicality of the extrinsic calibration method presented in the paper.     

对JJG52-2013在使用中的问题探讨CSCD

一般压力表主要用于液体、气体与蒸汽的压力测量,因广泛应用使得对其开展检定工作责任重大。随着压力表检定工作的深入开展,原检定规程JJG52-1999存在一些不适应的地方,国家质量监督检验检疫总局合并了JJG52-1999、JJG573-2003两个规程,于2013年6月24日发布了新规程JJG52-2013,用于弹性元件式一般压力表、压力真空表和真空表的检定工作。用新旧比对的方法分析新版检定规程的修订内容,对JJG52-2013在使用中的问题进行探讨,并在实际应用的基础上对新版检定规程提出了具体意见及建议。     

一起CFM56-7B发动机空中滑油量为“零”的故障分析

针对一起非典型的CFM56-7B发动机在空中显示滑油量为零、但落地后显示恢复正常的故障,结合发动机滑油系统工作原理,分析了故障可能的原因及采取的排故措施,排故经验可供其他同类发动机故障的处理借鉴。     

PLC仿真软件在涡流探伤电气系统设计中的应用

分析了涡流探伤系统和工艺流程,介绍了在涡流探伤电气系统中PLC输入输出信号地址的分配情况,然后基于对S7-PLCSIM界面的描述,利用S7-PLCSIM仿真实际的S7-300 PLC。实例表明：仿真结果与涡流探伤中实际的PLC运行一致,因此在电气系统设计过程中可利用S7-PLCSIM来查看程序的运行状况。     

PA44-180飞机起飞超转／大功率转速低故障分析

介绍7PA44—180飞机螺旋桨和调速器的结构和工作原理，分析了超转和大功率转速低故障的发生原因，并提出了切实可行的预防方法和排除故障的措施。     

Modeling and Simulation of Pipeline Security Monitoring System Based on Line-Structure Sagnac Interferometer with 3×3Coupler

The third damage action,human disruption behavior,is one of the major threats to pipeline operation.It is necessary to monitor and locate the perturbation behavior that may threat pipeline safety in real-time.Therefore,a new pipeline security monitoring system is designed by using line-structure Sagnac optic fiber interferemeter with the characteristic of 3×3coupler that can modulate the phase of optic signal,with no need for phase modulation and demodulation.The optic structure of the new system is simplified,the signal processing accuracy is improved,and the polarization effect is reduced.The working principle of the monitoring in ideal condition is described,the phase demodulation is analyzed and the location of the possible damage action point is formulated.By using simulink,the optic signal propagation and interference is simulated and interference signals in different frequencies are obtained.The results validate the feasibility of the monitoring system and indicate that the low frequency signal less than 1kHz resulting from the human damage action can be detected.The disturbance set at 10 km can be located by calculating the demodulation signal accurately over a long monitoring distance.     

某航空发动机环形燃烧室CO和UHC的数值计算

采用FLUENT软件对某型航空发动机燃烧室在最大和地面慢车状态进行三维、两相、湍流燃烧模拟,计算了CO和UHC的生成,获得了温度场、速度场和浓度场的数值。CO和UHC主要在低工况下生成,但油气比对污染物排放影响较大。     

CFM56-7B发动机推力等级改装的技术方法

介绍了CFM56-7B发动机推力等级、发动机推力更改的设计原理、系统构型差异以及推力更变设置的具体操作方法.     

Disturbances in the ionospheric F-region peak heights in the American longitudinal sector during geomagnetic storms of September 2005

In this paper, we use the modified GSM TIP model to explore how the thermosphere–ionosphere system in the American longitudinal sector responded to the series of geomagnetic storms on September 9–14, 2005. Comparison of modeling results with experimental data at Millstone Hill, USA (42.6°N, 71.5°W), Ramey, Puerto Rico (18.3°N, 66.8°W) and Jicamarca, Peru (11.9°S, 76.9°W) has shown a good agreement of ionospheric disturbances in the F-region maximum height. We examine in detail the formation mechanisms of these disturbances at different latitudes and describe some of the important physical processes affecting the behavior of the F-region. In addition, we consider the propagation of thermospheric wind surge and the formation of additional layers in the low-latitude ionosphere during geomagnetic storms.