模拟JJ—7飞机纵向摆动试飞研究

本文论述了BW-1变稳机空中飞行模拟H-7飞机发生两次纵向摆动时飞行状态特性,通过试飞研究其飞行品质,校核驾驶员诱发振荡(PIO)发生的可能性;并对解决PIO的方案进行了验证试飞研究,提出了排除PIO较适宜的参数值.试飞证明,空中飞行模拟试验是研究PIO的有效方法之一.     

Experimental and numerical investigation on surface quality for two-point incremental sheet forming with interpolator

The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator.     

高校委托工程审计的质量控制与评价指标体系构建

委托工程审计质量关系到高校工程审计职能的发挥和投资建设目标的实现.结合高校工程审计实践,探讨高校委托工程审计质量控制关键路径,并据此构建质量评价指标体系,以实现高校委托工程审计质量有效控制和科学评价.     

磁带机运转对星载CCD相机成像的影响

利用Ｌａｇｒａｎｇｅ方程,建立了磁带轮转动和卫星姿态振动相互影响的仿真模型,并用数值计算方法计算了卫星的姿态振动,仿真分析了对星载线阵ＣＣＤ成像质量的影响。     

激光辅助车削工艺参数对单晶硅表面质量的影响

为了提高单晶硅激光辅助车削加工表面质量,通过开展激光辅助和常规车削加工试验,结合表面粗糙度、表面形貌及拉曼光谱检测,研究激光辅助车削技术对加工质量的影响。基于正交试验方法,研究单晶硅激光辅助车削工艺参数对表面粗糙度的影响;通过方差分析和极差分析评估各因素对表面粗糙度的影响。研究结果表明：与常规车削相比,激光辅助车削可有效提高加工表面质量,降低材料表面的残余应力。主轴转速、进给速度、切削深度和脉冲占空比对表面粗糙度的贡献率分别为17.51%、44.48%、6.69%和14.70%。确定最佳加工参数组合如下：主轴速度为4 000 r/min,进给速度为2 mm/min,切削深度为5μm,脉冲占空比为30%,最终获得表面粗糙度Rq为2.4 nm的高质量表面。     

Grinding force and surface quality in creep feed profile grinding of turbine blade root of nickel-based superalloy with microcrystalline alumina abrasive wheels

Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles.     

行业标准与高职素质教育契合性理论与实践——以广州民航职业技术学院为例

高职院校在教育实践中存在着重技能培养而轻素质教育的问题,如何解决这一问题,将专业教育与素质教育相融合是一种切实可行方案。将专业教育中的＂行业标准＂与素质教育相结合,从＂贯彻教育方针,培育高素质人才＂、＂拓展职教潜能,达成校企融通＂、＂关注自身发展,践行学以致用＂三个维度描述二者契合的必要性,从在内涵上有着相通的意蕴、在历史上有着相同的源流、在操作中有着相融的环境三个角度论证二者契合的可行性,并总结广州民航职业技术学院基于行业标准的素质教育实践举措,即＂理论教学打基础＂、＂文化活动谋提升＂、＂顶岗实习检成效＂。     

高速公路卓越质量施工管理中六西格玛方法的运用

针对我国高速公路建设实际情况,结合我国高速公路的卓越绩效目标,综合考虑现行管理模式下突显出来的一系列问题,阐述在高速公路质量管理过程中引入六西格玛方法的现实可行性,并以用料和施工为例,提出该方法在高速公路质量管理过程中的具体实施步骤。     

航天器装配定位机构的设计与实现

航天器装配定位机构是重要的技术改造项目之一,用于舱段精密对接与分解,其通过与空间定位系统、自动起吊装置的配合,实现舱段对接与分解过程的量化识别与自动控制。该机构主要设计有质心捕获、自动调平和旋转等功能,为舱段对接与分解提供基础支撑平台、航天器空间姿态调整和相关数据支持。文章阐述了航天器装配定位机构原理,并对其主要功能的实现方法进行了设计。     

电子飞控飞机的飞行品质适航验证

FAA AC25-7A中的飞行品质评定方法 (HQRM)能够对使用电子飞控系统的民用运输机进行飞行品质评估。分析了HQRM评估程序以及相关适航要求,根据某民用飞机飞控系统功能危险分析,针对单侧升降舵卡阻这一典型故障,提出了在该失效状态下的模拟器飞行品质评估试验程序,分别给出了HQRM和相应军用标准评估方法,对军民评估方法的差异性和一致性进行了分析。研究结果对采用电子飞控系统的现代飞机的飞行品质适航验证具有工程参考意义。