远程教学网站的建设与管理

远程教学是当前地方党校系统普遍采用的一种新型教育教学方式,包括中央党校远程教学和农村党员远程教育。对中央党校远程教学网站的利用,可以采用“点课”、“辅导”、“大报告”等模式;对农村党员远程教育网站的利用,应重点考虑该站视频节目的应用。     

雷达信息显示中扫描线抑制问题分析

根据在混合显示方式下原始视频和综合信息显示的特点，分析了在综合信息显示时间不足的情况下，增大其显示时间的方法，如何保证固定的刷新频率，及自适应扫描线抑制方法中相应控制信号的产生过程，还分析了减少扫描线对原始视频信息显示的影响。     

时分式平面—立体电视图像转换器

时分式平面－立体电视图像转换器是由视频图像信号处理电路、控制信号产生电路和液晶眼镜驱动电路三部分构成，根据其构成和工作原理，可采用多种具体电路来实现。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

一种模拟视频信号亮度对比度校准方法

本文针对模拟视频信号长距离传输后信号衰减和偏移的问题,提出一种软件自动校准的方法。通过分析源端发送的校准图样,调整视频AD芯片的增益和偏移参数,达到最佳的亮度和对比度校准效果。     

非圆等距型面轮廓X-C轴联动高速磨削试验北大核心CSCD

针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。     

平面叶栅内固体粒子运动特性的研究

在利用高速摄影技术获得固体粒子在平面叶栅内运动特性的基础上, 采用Lagrangian轨迹法分别在考虑与不考虑边界层影响的情况下, 计算了固体粒子在叶栅内的运动轨迹和速度。通过与实验结果的比较发现:在利用Lagrangian法计算固体粒子的运动特性时, 对于尺寸比较大的粒子可以不考虑边界层的影响, 而对于尺寸比较小的粒子则需考虑边界层的影响。      

基于模板匹配整帧屏幕视频帧内无损编码方法

当前主流的视频压缩标准,如H.264、HEVC等,主要是针对摄像机拍摄的视频而设计的.而屏幕内容(SC)的视频是由计算机生成的,无噪声,要求更高的压缩效率,同时与摄像机拍摄的视频相比包含更多的结构相似性.提出了一种利用屏幕视频中相似性的模板匹配帧内编码方法,采用由21个像素点组成的模板,以像素点为最小单位对整帧进行模板匹配,并使用哈希函数实现高效的模板查找,最后对残差图像进行熵编码.实验结果显示,与标准的HEVC扩展方法相比,该方法在无损编码上压缩率可以提高一倍,编码时间减小了近一半.