单/双轴预拉载荷对碳纤维复合材料高速冲击性能的影响研究

针对发动机工作时受预载荷的叶片受到外物冲击的情况,设计一种面内单轴及双轴预加载装置,开展单轴与双轴不同大小预拉载荷下碳纤维/环氧树脂复合材料（T700/TDE-86）的高速冲击试验,探究预拉载荷对复合材料抗冲击性能的影响,并结合超声C扫描分析预拉载荷对损伤面积的影响。结果表明：面内初始载荷对复合材料层合板抗冲击性能和分层损伤面积有显著影响;预拉载荷会提高靶板的抗弯刚度,减少靶板吸收的能量,减小弹道极限,且在双轴预拉情况下更明显;弹体击穿靶板后分层损伤面积几乎不变,而预拉载荷会减小分层损伤面积,且在双轴预拉情况下更明显。     

滚珠自转对高速球轴承环下润滑内部流动的影响

高速球轴承正常工作时,处于高速旋转状态,此时油相和气相因重力和离心力的作用在轴承环间剧烈运动。为了更准确地分析轴承环间的两相流动,采取VOF模型进行内部流场的模拟,采用多重旋转坐标系描述部件运动。建立球轴承环下润滑计算模型,分析了考虑滚珠自转因素下轴承内部的流动,并在此基础上探究了转速及供油量对轴承工作状态的影响。结果表明,对比整体模型与滚珠自转模型,发现滚珠自转使得轴承内部油体积分数增大,同时也使得滑油穿透间隙达到外环的能力增加;在考虑滚珠自转情况下,转速的不断增大,使得轴承内部的油相体积分数不断减小,在低转速情况下滚珠自转对流体运动影响较为明显,在高转速情况下公转速度对流体运动起到主导作用,滚珠自转对流体运动影响减弱;供油量不断的增大,使得滚珠自转模型内部的油相体积分数也在不断增大,而且滚珠自转运动会加强滑油在轴承内部的分布。     

某直升机主减速器传动系统的寿命与可靠性计算方法

通过对直升机典型任务剖面原始载荷数据谱进行统计处理,经三维有限元分析将所编系统载荷谱转化为齿轮应力谱;结合Goodman公式及材料P-S-N曲线(给定存活率下的疲劳寿命曲线)算出该系统各齿轮在各级载荷下的疲劳寿命,利用统计软件Minitab对寿命数据进行分析,得出齿轮的接触疲劳寿命服从两参数威布尔分布,根据威布尔分布的...     

高速SpaceWire协议IP的可靠性增强方法

针对航天高速SpaceWire总线系统对协议IP的高可靠性要求,提出一种用于静态随机访问存储器(SRAM)型现场可编辑逻辑门阵列(FPGA)的增强三模冗余(TMR)方法。该方法对传统三模冗余和部分三模冗余做了改进,将需要进行三模冗余的原设计分为一般单元集和可靠性薄弱的关键单元集,对一般单元集中的每个单元做三模冗余,对关键单元集中的每个单元做顺序四模冗余。给出了顺序四模冗余的可靠度计算式和表决器的布尔表达式。建立了系统可靠性的马尔科夫模型并基于模型开展了可靠性仿真。仿真结果表明增强三模冗余系统的可靠性不仅明显优于传统三模冗余系统,而且优于部分三模冗余系统,使系统可靠性得到有效提高。     

SAR高速实时信号处理系统设计

合成孔径雷达回波数据速率一般高达3GSPS,如何采集、存储、压缩、传输如此高速率的数据成为一个难点。文章在分析了SAR回波数据特点的基础上,设计并实现了一个SAR高速实时信号处理系统。该系统以FP-GA为核心处理器、ADC08D1500为高性能的AD采集芯片、DDR_SDRAM为数据存储器、TLK2711为数据传输芯片。实验结果表明：本文设计的高速实时信号处理系统性能良好,能够很好地实时处理高速率的SAR回波数据。同时该系统易于实现,具有较强的实用性。     

高速数字图像数据传输的研究及实现

随着CCD相机几何分辨率和辐射分辨率的提高,其数据传输速率越来越高,传输通道也越来越多,因此对相机与采集卡之间（或者数传设备）的接口性能提出了更高的要求。文章基于并／串（串／并）转换功能的芯片．研究探讨了一种高速数字图像传输方法,可提高数据传输率,减少电缆数量,提高可靠性,为实现航天相机的轻型化、小型化作出一定的贡献。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

非圆等距型面轮廓X-C轴联动高速磨削试验北大核心CSCD

针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。     

平面叶栅内固体粒子运动特性的研究

在利用高速摄影技术获得固体粒子在平面叶栅内运动特性的基础上, 采用Lagrangian轨迹法分别在考虑与不考虑边界层影响的情况下, 计算了固体粒子在叶栅内的运动轨迹和速度。通过与实验结果的比较发现:在利用Lagrangian法计算固体粒子的运动特性时, 对于尺寸比较大的粒子可以不考虑边界层的影响, 而对于尺寸比较小的粒子则需考虑边界层的影响。