Topology Optimization Design for the Layout of theMain Bearing Joint of a Certain Aircraft

为了实现飞机部件的轻量化设计,将拓扑优化和代理模型相结合构建了一个结构布局优化的算法。以某型飞机主承力接头为研究对象,根据结构传力路线和工艺要求,将接头的布局优化转化为耳片的平面拓扑优化与螺栓位置的优化。以接头耳片的厚度和中间排螺栓位置作为布局变量,对每组布局变量下的耳片进行拓扑优化,对布局变量采用基于代理模型的遗传算法进行优化。以质量最小为优化目标,在强度与刚度的多约束条件下,完成了某型飞机主承力接头的布局拓扑优化。结果表明,本方法的优化结果比传统的拓扑优化结果减重约 14.5%,验证了优化算法的可行性与有效性。     

航空发动机高速滚子轴承动态特性分析

 高速滚子轴承的动态特性对航空发动机转子系统的性能有重要的影响,为得到较准确的轴承动态性能,采用拟动力学法建立承受四自由度载荷的滚子轴承动力学分析模型,模型中各零件之间的力和力矩由建立的轴承零件相互作用模型计算得到,并使用较精确的弹流模型计算拖动力,给出了非圆滚道轴承动态性能的计算方法。通过算例分析了工况参数和结构参数对滚子轴承动态特性的影响规律,最后通过实验结果验证了程序的可靠性。滚子轴承动态特性的研究为研究航空发动机转子-轴承动态性能耦合分析奠定了基础。     

航空发动机球轴承剥落故障模式分析

为研究航空发动机球轴承的剥落故障模式,利用原子发射光谱技术、自动磨粒分析技术、铁谱技术及能谱分析技术对球 轴承加速等效试验滑油中磨粒的数量、大小、形貌及成分等信息进行分析。结果表明：金属颗粒污染物导致轴承出现初始疲劳剥 落;球轴承剥落的特征磨粒为滚动疲劳磨粒和球形磨粒,内衬套微动磨损的特征磨粒为铁的黑色氧化物和红色氧化铁磨粒;临近 轴承失效时,滑油中Fe元素质量分数由7.49×10 -6 增大至21.74×10 -6 ,特征磨粒数量也由48.9个/mL急剧增加至1433.8个/mL,且特 征磨粒直径主要分布在25～50 μm。金属颗粒污染物的存在使轴承承力内半圈滚道加速出现接触疲劳剥落,滚道剥落到一定程 度后,在轴向力、摩擦力及预紧力等综合作用下在内衬套与承力内半圈接触处发生微动磨损,进一步加剧了滚道的疲劳剥落,最终 导致球轴承失效。     

基于LTSA融合降维法的滚动轴承可靠性评估方法

为了保障滚动轴承在给定工况下安全平稳地运行,提出了一种基于局部切空间排列(LTSA)和威布尔比例故障率模型(WPHM)的滚动轴承可靠性评估方法.该方法提取滚动轴承整个寿命周期的时域、频域、时频域及统计等不同分析域上的特征指标,从中筛选出包含滚动轴承运行状态的特征指标,构建出高维多域特征集;利用局部切空间排列算法对高维多...     

Flame features and oscillation characteristics in near-blowout swirl-stabilized flames using high-speed OH-PLIF and mode decomposition methods

Flame features and dynamics are important to the explanation and prediction of a lean blowout (LBO) phenomenon. In this paper, recognition of near-LBO flame features and oscillation characterization methods were proposed based on flame spectroscopic images. High-speed planar laser-induced fluorescence measurements of OH were used to capture unique dynamic features such as the local extinction and reignition feature and entrained reactant pockets. The Zernike moment demonstrated a good performance in recognition of stability and near-LBO conditions, though the geometric moment had more advantages to characterize frequency characteristics. Low-frequency oscillations, especially at the obvious self-excited oscillation frequency around 200 Hz, were found when approaching an LBO condition, which can be expected to be used as a novel prediction characteristic parameter of the flameout limit. Proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) were used to conduct dynamic analysis of near-LBO flames. POD modes spectra showed the unique frequency characteristics of stable and near-LBO flames, which were basically in line with those at the heat-release frequency. The primary POD modes demonstrated that the radial vibration mode dominated in a stable flame, while the rotation mode was found to exist in a near-LBO flame. Analysis of modal decomposition showed that flame shedding and agminated entrained reactant pockets were responsible for generating self-excited flame oscillations.     

喷注角度对超声速气流中液体横向射流的影响

为探索超声速气流中变角度组合射流对喷注雾化过程的影响，采用高速摄影和基于KH-RT破碎模型的欧拉-拉格朗日数值仿真方法开展研究，仿真结果和实验吻合较好。研究表明，同一流量下逆流喷注，可以较为有效地增强混合效果，提升射流穿透深度。带扩张型面内液雾穿透深度呈现先增大后降低的趋势。等流量条件下顺流双孔喷注有效截面面积大体一致，略低于单孔直喷。等效流量下逆流喷注所得液雾截面面积收益最为明显。截面平均粒径方面，单孔喷注雾化粒径基本一致，顺流双孔喷雾粒径较小。等压降顺流对喷由于流量较大，雾化质量相对较差，平均粒径最大。     

Physics-based model for boundary layer transition prediction in a wide speed range

A new physics-based model employing three transport equations is developed for the simulation of boundary layer transitions in a wide speed range. The laminar kinetic energy is used to represent pretransitional streamwise velocity fluctuations, taking account of different instability modes. The fluctuation velocity components normal to the streamwise direction are modeled by another transport equation. Transition is triggered automatically with the development of the pretransitional velocity fluctuations. In the fully turbulent region, the model reverts to the k-ω turbulence model. Different test cases, including subsonic, supersonic and hypersonic flows around flat plates, airfoils and straight cones, are numerically simulated to validate the performance of the model. The results demonstrate the excellent predictive capabilities of the model in different paths of transition. The model can serve as a basis for the extension of additional transition mechanisms, such as rotation and curvature effects, roughness-induced transition and crossflow-induced transition.     

大型对日定向装置大开口复合材料主承力架传力设计及验证

根据大型对日定向装置的结构特点和受力特性，调整传力结构，充分利用纤维增强复合材料结构的可设计性，开展优化设计。在保证高刚度和轻量化的同时，克服结构大开口带来的承载能力不足，设计出结构质量与承载比仅为5.2%，集舱段和壳体功能于一体的大型对日定向装置复合材料主承力架结构。建立有限元模型，分别采用Tsai-Wu和最大应变2种纤维增强复合材料的强度失效准则，对其进行校核。开展静力试验，采集应变等信息，与有限元仿真分析结果展开对比。结果表明:其整体趋势一致，顺利通过试验考核。     

高温环境下角接触球轴承磨损寿命分析

针对高温环境下轴承材料性质和润滑状态变化，造成轴承磨损加剧，过早丧失精度的问题。首先开展高温环境下轴承用材料的摩擦磨损试验，获取材料的磨损系数。在此基础上，考虑温度、润滑、轴承材料属性等对轴承磨损性能的影响，建立高温角接触球轴承磨损模型，通过数值求解探讨工况参数和结构参数等对轴承磨损性能的影响，并评估轴承的磨损寿命。结果表明：对于高温轴承材料无磁合金GH05，在高温300 ℃摩擦状态下平均磨损系数为2.5×10^-7 mm²/N；随着载荷、转速、温度的增加，轴承内、外滚道的磨损率均不断增大，其中内圈磨损率大于外圈，内圈磨损特性决定着轴承的磨损寿命；载荷和转速是决定轴承磨损寿命的主要因素，轴承主结构参数对磨损寿命具有重要影响，通过结构优化可提高轴承磨损寿命。     

某扭力管万向节组件及支撑轴承的正弦振动疲劳研究

本文建立C919某扭力管万向节组件及支撑轴承的有限元模型，对其进行模态分析及正弦分析，推导了正弦振动下的疲劳寿命计算公式并预估了模型的寿命，通过模态试验验证了模型的正确性，通过正弦试验验证了疲劳寿命计算的正确性。该疲劳寿命计算方法可用来预估相关模型的正弦振动疲劳寿命。