一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

液化天然气作为航空燃料的发展趋势及特点分析

为研究液化天然气(LNG)作为航空燃料的可行性,对LNG的特点、发展趋势及作为航空燃料存在的问题进行了分析.采用了横向比较的方法,将LNG与新的航空替代燃料和传统航空燃料进行了比较和计算分析.结果表明:与新的航空替代燃料相比,LNG具有来源广泛、经济性好、发动机适应性强等优点.与传统航空燃料相比,LNG的储量大,可使用100年以上;可燃极限宽、污染物排放低,NOx排放仅为航空煤油的1/4;单位质量能量密度高、成本低,其燃料成本仅为航空汽油的一半,航空煤油的1/3;同时还具有可用于发动机高温部件冷却用的冷能,是一种极富潜力的航空燃料.指出在LNG作为航空燃料方面急需开展动力系统与飞机结构的匹配、燃料相态的有效转化及不同燃料在燃烧室内的反应特性等方面的研究工作.      

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

Al/Ni含能多层膜在Al2O3陶瓷/不锈钢焊接中的应用

采用磁控溅射设备,生长AuSn合金做焊料层、Al/Ni含能多层膜做热量提供层,实现了不锈钢和Al_2O_3间的异质材料自蔓延高温扩散焊。利用SEM、XRD和DSC等测试手段表征AuSn合金和Al/Ni含能多层膜的微观形貌、相成分和放热量;用万能试验机测试焊接接头的力学性能。结果表明,AuSn合金的质量比基本达到80∶20,而多层膜的层状结构清晰,反应热达到1 239 J/g。焊接实验结果表明,仅使用AuSn焊料时,剪切强度仅为46 MPa,在增加Al/Ni含能多层膜后,其剪切强度可达90 MPa,强度提高了约一倍。焊接接头的界面显微形貌和相结构研究表明,剪切强度的增强主要是Al/Ni多层膜提供了额外能量使得界面处的反应剧烈,陶瓷金属化层与中间层的反应加剧,形成了新的反应生成物。     

活塞式航空煤油发动机冷启动性能试验

针对启喷转速、燃油温度、点火能量等影响因素,在一台排量650 mL的单缸试验机上,开展了对航空煤油发动机冷启动性能的试验研究。结果表明:随着启喷转速的提高,启动时间呈现先变短后变长的趋势,启喷转速为1 200 r/min时启动时间最短;燃油温度的提高对冷启动性能和燃烧特性都有提升,在本文试验条件下,燃油温度为50 ℃时即可成功启动;提升点火能量对火核形成和火焰传播都有积极影响,可显著缩短启动时间,但当点火能量增大到75 mJ之后,其改善作用已不明显。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

发动机唇口电热防冰系统性能仿真

采用三维耦合传热方法对发动机唇口电热防冰系统进行了多状态下的性能仿真,获得了唇口表面平衡温度及动态温升响应时间,以此评估防冰系统性能,并通过与冰风洞试验结果对比,对仿真过程进行了修正。研究表明:唇口表面加热区平衡温度均高于273.15 K,温升响应时间小于60 s,满足防冰需要,较为严酷的防冰状态点主要为飞行速度较大、环境温度较低的状态点;修正唇口材料导热系数后,仿真与试验结果吻合良好。研究结果能有效指导工程研制,对提高防除冰仿真分析结果的准确性提供了很好的借鉴。     

基于对偶四元数的捷联惯导算法在发射点惯性系下的应用研究

针对导弹类载体在做复杂的高动态机动时,采用传统的捷联惯导算法容易产生圆锥误差与划船误差,从而导致解算精度降低的问题,在发射点惯性系下设计了基于对偶四元数的捷联惯导算法.在建立发射点惯性系下的捷联惯导解算模型的基础上,详细推导了基于对偶四元数的捷联惯导解算算法,通过对比分析其中的速度更新过程与传统算法的差异,说明该算法可...