Crystal orientation and morphology of α lamellae in wrought titanium alloys: On the role of microstructure evolution in β processing

To obtain high-quality aviation forgings of titanium alloys, β forging is an essential processing step which must be considered throughout a production process. In this work, the effect of β forging on the crystal orientation and morphology of lamellar α was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during β working resulted in the formation of low-angle grain boundary (LAGB_β) inside β grains. The lamellar α can penetrate through the LAGB_β, leading to similar intra α LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed. A continuous change of the β orientation in diffusive boundaries results in the formation of fine and disordered α lamellae without intra-lamellar boundary to hold the Burgers orientation relationship (OR). On sharp boundaries, it is prone to producing continuous grain boundary α (α_GB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary α for a smoother orientation change on the β grain boundary.     

空心长轴深孔加工工艺研究

以某发动机空心长轴零件深孔加工为研究对象,设计了长径比为15,长度超过1米的整体硬质合金刀杆,在某加工项目试验中,应用这种超长整体硬质合金刀杆,在细长比大于10的空心长轴的深孔镗削加工中,改变了传统的深孔加工工艺,满足了空心长轴深孔加工中严格的壁厚差要求,取得了明显的效果.     

激光深熔焊接等离子体发射光谱诊断研究

综述了激光等离子体发射光谱诊断的基本假设;介绍了电子温度、密度光谱计算最常用的方法;同时综述了国内外激光焊接等离子体光谱诊断的研究进展.旨在对激光焊接等离子体光谱诊断基本理论和当前的研究进展进行全面的梳理,并对开展激光焊接等离子体光谱试验工作提供理论支持和技术参考.     

降低CC50汽轮机推力瓦运行温度研究

针对4#机组汽轮机出现正推力瓦运行金属温度偏高的状况,在深入调查4#机组汽轮机现状的基础上,通过与现有标准相比较,确定目标为正推力瓦运行金属温度≤95℃;在具体分析其影响因素的基础上,确定了5个主要影响因素,并针对其采取了相应措施,改造结果表明确实使4#机组汽轮机组正推力瓦运行金属温度低于95℃,达到了预期目标,为汽轮机的改造提供了技术指导。     

Effect of surface roughness on microwave brightness temperature from lunar surface: Numerical analysis with a hybrid method

A hybrid method, combining the radiative transfer theory and the method of moments (MoM), is proposed to study the potential effect of the lunar surface roughness on the microwave brightness temperature. The total upward emission reaching the lunar surface from below media is calculated by the radiative transfer theory, and then the brightness temperature is obtained by weighting the bidirectional transmission coefficients which is computed using the MoM. The method is validated by both flat and rough surface models with analytic solutions. With the hybrid method, brightness temperatures from simulated lunar model are calculated and compared to those from a flat layered model. The comparisons show that the effect of rough surface on brightness temperature cannot be ignored and also depends on many other factors, such as observation angle and polarizations. For vertical polarization, an optimal observation angle may exist to reduce the effect of surface roughness. These results indicate that the knowledge of lunar surface roughness is important in microwave remote sensing to the Moon and may probably provide a guide to lunar projects in future.     

2A12 铝合金锻坯开裂故障分析

某产品用2A12铝合金锻坯在生产过程中发生开裂故障。本文对开裂锻坯进行了形貌观察与断口分析,并对比研究了热处理后开裂锻坯、未热处理锻坯和原材料铝棒。结果表明:开裂锻坯上的开裂模式为脆性开裂;开裂锻坯上的裂纹形成于热处理过程,形成原因应与锻造工艺控制不当导致锻坯在热处理过程中形成的粗晶有关。     

切削加工优化研究

本文通过切削加工机理的研究，建立了切削加工的数学模型，为难加工材料切削用量的选择提供了科学的方法。     

大功率柴油机排气阀机器人焊接系统及工艺

为了提高船舶焊接质量,采用机器人柔性化焊接系统堆焊镍合金阀盘。设计了高效、高质量的机器人焊接系统,对SNCrW不锈钢进行了焊接工艺研究,并对样件进行了检验分析。经检验,不存在超过0.06mm的缺陷,完全符合阀盘质量检测标准,属于合格产品,完成了国内首个高质量镍基堆焊阀盘的焊接。     

Dependence of creep age formability on initial temper of an Al-Zn-Mg-Cu alloy

The initial temper of the material may directly affect the whole creep age forming(CAF)process. In terms of creep deformation and stress relaxation, using the constant-stress creep aging and constant-strain stress relaxation aging tests, the relationship between initial temper and CAF formability is investigated for an Al-Zn-Mg-Cu alloy at 165 °C for 18 h. Three tempers are selected as the initial tempers in CAF, viz., solution, retrogression and re-solution. The CAF formability of this alloy with initial temper of retrogression is the best, and the creep strain of the retrogression tempered specimen after creep aging of 18 h is about 1.21 and 1.34 times than that of the solution and the re-solution tempered specimens, respectively. The calculated stress exponents of this alloy with three initial tempers range from 7.3 to 9.5, indicating that the CAF of this alloy is mainly controlled by the dislocation creep. The various formability for three initial tempers are attributed to different inhibitions of the transgranular precipitates on the dislocation movement. For the retrogression temper, the initial fine and uniformly distributed precipitates are seriously coarsened after6 h of CAF, which minimally inhibit the dislocation movement. While, for the re-solution temper,the fine precipitates are re-precipitated in the matrix of the alloy, which observably hinder the dislocation movement and lead to the worst formability.     

时序信号设计的一种新方法

文章结合高速时序工作的特点，从实现的角度提出了一种利用软件调整时序的新方法。在可编程逻辑器件中，利用数字时钟管理器（DCM），通过模块化和增量式设计思想达到对高速时序信号的精确调节。最终实现了一个20MHz速率的时序控制，调节精度达到100ps。