多喷口环量控制翼型流动的研究

提出了多喷口环量控制翼型的想法，并进行了数值研究。结果表明，多喷口环量控制方法可以在中、小Ｃμ吹气时提高翼型的升力和减小能耗，并能改善环量控制翼型在较高来流马赫数下的气动性能，避免“压缩性失速”。     

Effect of surface blowing on aerodynamic characteristics of tubercled straight wing

Recent research proves that wings with leading-edge tubercles have the ability to perform efficiently in post-stall region over the conventional straight wing. Moreover, the conventional straight wing outperforms the tubercled wing at a pre-stall region which is quintessential. Even though tubercled wing offers great performance enhancement, because of the complexity of the flow, the trough region of the tubercled wing is more prone to flow separation. Henceforth, the present paper aims at surface blowing – an active flow control technique over the tubercled wing to enhance the aerodynamic efficiency by positively influencing its lift characteristics without causing any additional drag penalty. Flow parameters like blowing velocity ratios and the location of blowing were chosen to find the optimised configuration keeping the amplitude and frequency of the leading-edge tubercles constant as 0.12 c and 0.25 c respectively. Numerical investigations were carried out over the baseline tubercled wing and tubercled wing with surface blowing at various blowing jet velocity ratios 0.5, 1 and 2 over four different chordwise locations ranging from 0.3 c to 0.8 c.The results confirm that blowing at various x/c with different blowing velocity ratios performs better than the conventional tubercled wing. Comparatively, blowing velocity ratio 2 at 0.3 c shows peak performance of about 28% enhancement in the lift characteristics relative to the baseline model. Particularly, in the pre-stall region, 25–50% increase in aerodynamic efficiency is evident over the tubercled wing with surface blowing compared with the baseline case. Additionally,attempts were made to delineate the physical significance of the flow separation mechanism due to blowing by visualizing the streamline pattern.     

高效液力偶合器轮系参数分析研究

高效液力偶合器额定工况无滑差的特点，使大功率（＞ ３００ ｋ Ｗ ）液力偶合器发热问题得到根本解决。就其设计方法进行分析，提出了斗轮及斗叶数的确定方法，并通过样机试验了解该偶合器的特性。     

非结构混合网格自适应并行技术

计算流体力学（CFD）模拟实际工程问题所采用的网格规模可达千万量级，并行技术是减少计算时间的有效方法。耦合流场信息的网格自适应技术能有效动态优化计算网格，被NASA视为一项亟待发展的CFD关键技术。混合网格自适应系统包含网格分布优化、表面网格投影和空间网格匹配等关键技术。针对以上3项关键技术分别建立了高效的并行算法。首先，提出了"先唯一后同一"的两步法策略实现了网格单元分布优化过程的并行相容性；其次，基于局部曲面拟合思想，实现了曲面重构和新增物理网格点投影的完全并行；再次，提出了空间网格匹配技术的半并行算法，快速解决了网格单元交错问题。为了提高后续流场计算的并行效率，发展了基于并行重分区-网格数据迁移方法的动态负载平衡技术，并采用圆柱激波流场自适应模拟对动态负载平衡技术进行初步验证。最后，采用三角翼自适应加密测试了自适应系统的并行效率。结果表明，建立的混合网格自适应系统并行效率较高，且相比流场求解耗费总时间的比例低于1%。     

铸钢用保温冒口及其应用研究

本文针对提高铸钢件冒口补缩效率问题，给出了微珠保温冒口的配方及生产工艺；并介绍了其在生产中的具体应用。保温冒口的使用，改善了铸件质量，并大幅度提高了企业经济效益。     

V型尾翼布局弹性体飞机操纵性分析

使用静气动弹性分析方法,对双尾撑V型尾翼布局飞机纵向静气动弹性特性随飞行动压、迎角、尾撑纵向弯曲刚度的变化趋势进行了分析,以期为类似布局飞机的设计提供参考。尾撑结构刚度对飞机的俯仰、偏航的操纵效率都有较大影响,需要结合飞行动压范围和质量要求合理选择尾撑结构的材料和尺寸,在设计时,严格控制尾撑的刚度指标。     

Design and numerical investigation of swirl recovery vanes for the Fokker 29 propeller

Swirl recovery vanes（SRVs） are a set of stationary vanes located downstream from a propeller, which may recover some of the residual swirl from the propeller, hoping for an improvement in both thrust and efficiency. The SRV concept design for a scaled version representing the Fokker 29 propeller is performed in this paper, which may give rise to a promotion in propulsive performance of this traditional propeller. Firstly the numerical strategy is validated from two aspects of global quantities and the local flow field of the propeller compared with experimental data, and then the exit flow together with the development of propeller wake is analyzed in detail.Three kinds of SRV are designed with multiple circular airfoils. The numerical results show that the swirl behind the propeller is recovered significantly with Model V3, which is characterized by the highest solidity along spanwise, for various working conditions, and the combination of rotor and vane produced 5.76% extra thrust at the design point. However, a lower efficiency is observed asking for a better vane design and the choice of a working point. The vane position is studied which shows that there is an optimum range for higher thrust and efficiency.     

时序信号设计的一种新方法

文章结合高速时序工作的特点，从实现的角度提出了一种利用软件调整时序的新方法。在可编程逻辑器件中，利用数字时钟管理器（DCM），通过模块化和增量式设计思想达到对高速时序信号的精确调节。最终实现了一个20MHz速率的时序控制，调节精度达到100ps。     

基于混沌遗传算法优化神经网络方法的救护直升机效能评估与指标优化研究

采用遗传算法与神经网络相结合的方法研究救护直升机的效能评估,建立了评估指标与效能评估值的非线性关系,克服了传统线性评估方法的不足,结果表明GA-BP算法能够很好地评估救护直升机效能,并保持了很高的精确度;同时,采用BP-GA算法对救护直升机的指标进行了优化,结果同样表明该方法可以有效地优化救护直升机的指标.     

Is there an instrumental drift in the counting rate of some high latitude neutron monitors?

For the last six decades the neutron monitors have provided a continuous string of very reliable data to the heliophysics community. Although neutron monitors are not the primary source of data for the galactic cosmic rays, these data serve as a baseline reference for the data collected by the detectors on board the satellites and deep space probes, far away from earth orbit. The pressure corrected hourly data are available from the World Data Centers. These data have been used to derive deep insights pertaining to the electromagnetic states of the heliosphere and the modes of transport of energetic charged particles in the tangled interplanetary magnetic fields. We present evidence that some of the high latitude neutron monitors are undergoing long-term drifts in their baselines. In particular, we argue that there is no physical basis to justify the observed long-term downward trend in the baseline of the South Pole neutron monitor. The real reason may have to do with its maintenance at a distant location with challenging logistics and an improper normalization of its data after the 26 months break in the 1970s.