航空武器作战效能的算法

在介绍航空武器作战效能概念的基础上,提出了计算航空武器作战效能的算法,建立了数学模型,并且依此模型给出了计算实例,结果证明其计算结果与试验结果一致,因而该方法有效。     

同温层气球平台反向定位系统的研究

反向定位系统是针对驻留型同温层气球平台的一种新型定位系统 ,该系统的基本原理是由接收站的位置计算得出发射机的位置。文章采用卡尔曼滤波的方法 ,建立了反向定位系统的模型 ,给出其滤波算法 ;鉴于地面接收站的位置选择对该系统的定位精度有较大的影响 ,给出地面站选址依据 ,并通过计算、仿真获得一组较为理想的布站方式。此外 ,钟差是系统的一个主要误差源 ,文中对其引起的定位误差进行了分析 ,并给出估算的方法 ;对系统中的传播误差、设备误差也进行了分析。最后 ,对系统建立了仿真模型进行仿真。结果表明 ,该定位系统具有较好的定位精度     

用推力矢量控制技术改进超声速飞行器空气动力特性

为了提高某超声速飞机的空气动力学效率和机动性能,本文采用低阶的三维板块法和DATCOM半经验公式,在亚声速和超声速条件下,对不同马赫数和迎角情况计算了基本气动外形的飞机空气动力学特性、表面压力分布以及最大升力。此外还开发了一套软件以实现由引进的先进气动操纵面（如鸭翼等）控制的二维推力矢量技术。试验结果表明：气动操纵面结合推力矢量技术能够产生足够的低头力矩,且有能力满足高度机动飞行时的稳定性要求。此外,不论是亚声速还是超声速飞行,气动操纵面均可以提高气动效率5％-6％。     

Time delay compensation in lateral-directional flight control systems at high angles of attack

The previous studies of time delay compensation in flight control systems are all based on the conventional aerodynamic derivative model and conducted in longitudinal motions at low angles of attack. In this investigation, the effects of time delay on the lateral-directional stability augmentation system in high-α regime are discussed based on the $\dot{\beta }$ model, which is proposed in our previous work and proved as a more accurate aerodynamic model to reveal the lateral-directional unsteady aerodynamic characteristics at high angles of attack. Both the $\dot{\beta }$ model and the quasi-steady model are used for simulating the effects of time delay on the flying qualities in high-α maneuvers. The comparison between the simulation results shows that the flying qualities are much more sensitive to the mismatch of feedback gains than the state errors caused by time delay. Then a typical adaptive controller based on the conventional dynamic derivative model and a gain-prediction compensator based on $\dot{\beta }$ model are designed to address the time delay in different maneuvers. The simulation results show that the gain-prediction compensator is much simpler and more efficient at high angles of attack. Finally, the gain-prediction compensator is combined with a linearized $\dot{\beta }$ model reference adaptive controller to compensate the adverse effects of very large time delay, which exhibits excellent performance when addressing the extreme conditions at high angles of attack.     

氧化镍电致变色薄膜及其器件的制备与性能研究

以氧化铟锡(ITO)玻璃为基底,采用直流反应磁控溅射法在室温环境下制备了高透过率调制的NiO_x薄膜,利用X射线衍射仪(XRD)、扫描电子电镜(SEM)、紫外可见分光光度计(UV 3600)对薄膜进行分析和表征,研究溅射过程中氩氧比、气压、功率对薄膜结构、形貌及电致变色性能的影响。结果表明：制备的NiO_x薄膜表面有明显的结晶颗粒及孔隙,并沿(200)晶面择优生长;随着气压、功率、氧分压的增大,透过率调制先增大后减小,在时间为45 min、溅射气压4.9 Pa、氩氧比113∶7、功率215 W时最高可达58.3%,着褪色响应时间分别为9和19s,相应的着褪色效率分别为77.56和40.39 cm²/C;以最优工艺的NiO_x薄膜组装了结构为Glass/ITO/NiO_x/Li-electrolyte/WO₃/ITO/Glass的电致变色器件,器件在550 nm处的光调制幅度为46.5%,着褪色时间分别为27和45 s,相应的着褪色速率为1.5和0.9%/s,在循环...     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

强海杂波背景下目标检测方法综述

高频地波雷达被广泛应用于海面目标的检测,而由于海杂波的分布散射具有很强的动态特性,通常情况下成为了海面目标检测的主要干扰成分。因此,在强海杂波背景下进行目标检测的关键在于如何有效抑制海杂波。从循环对消、子空间分解、模型预测以及分形特征这几方面对海杂波抑制技术进行综述、分析和总结,为后续对海面目标检测提供参考。     

不同边界层厚度下高马赫数进气道自起动过程研究

为了探寻入口边界层厚度变化对高马赫数进气道自起动性能的影响,对简化的二元高马赫数进气道的加速自起动过程进行数值仿真研究,分析了边界层厚度对自起动过程中流场波系结构变化和自起动性能的影响机制,获得了不同边界层厚度下的进气道自起动性能及主分离包高度的变化规律。结果表明:随着边界层相对厚度从0.05增加至0.3,进气道的自起动马赫数一开始保持不变,然后快速增大;相同主流条件下,不起动流场跨越主分离包无量纲压升和主分离包高度随边界层相对厚度的增大均变小;边界层动量损失厚度和跨越主分离包无量纲压升对进气道起动性能影响重大。     

硅橡胶基防热涂层动态烧蚀行为及机理研究

针对两种典型硅橡胶基防热涂层开展高温燃气流烧蚀实验，通过对烧蚀后涂层的宏观及微观形貌分析，探讨了其防隔热机理及烧蚀模型。研究结果表明：烧蚀后两种涂层均存在液态层、陶瓷层、热解层以及原始层；烧蚀过程中甲基苯基硅橡胶涂层主要发生主链“回咬”成环反应，导致树脂基体交联密度降低，力学性能下降，涂层外表面发生开裂，甲基乙烯基硅橡胶涂层则主要发生侧基交联反应，使树脂基体交联密度上升，促进涂层发生陶瓷化转变；热辐射、热容吸热、热解反应吸热以及热阻塞效应为四种主要的热耗散机制，质量损失产生的原因主要包括反应气体释放以及气动剪切力导致的机械剥蚀。     

非结构CFD软件MPI+OpenMP混合并行及超大规模非定常并行计算的应用

常规工程应用中，非定常数值模拟（如多体分离）的计算量十分巨大，如果为了达到更高的计算精度，加密网格或者采用高精度方法将会使得计算量进一步增大，导致非定常数值模拟在CFD工程应用中成为十分耗时和昂贵的工作，因此，提高非定常数值模拟的可扩展性和计算效率十分必要。为充分发挥既有分布内存又有共享内存的多核处理器的性能和效率优势，对作者团队开发的非结构网格二阶精度有限体积CFD软件（HyperFLOW）进行了混合并行改造，在计算节点间采用MPI消息传递机制，在节点内采用OpenMP共享内存的MPI+OpenMP混合并行策略。首先分别实现了两种粒度（粗粒度和细粒度）的混合并行，并基于国产in-house集群采用CRM标模（约4 000万网格单元）定常湍流算例对两种混合并行模式进行了测试和比较。结果表明，粗粒度在进程数和分区数较少的小规模并行时具有效率优势，16线程时效率较高；而细粒度混合并行在大规模并行计算时具有优势，8线程时效率较高。其次，验证了混合并行在非定常计算情况下的可扩展性，采用机翼外挂物投放标模算例，分别生成3.6亿和28.8亿非结构重叠网格，采用对等的（P2P）网格读入模式和优化的重叠网格隐式装配策略，网格读入和重叠网格装配耗时仅需数十秒；采用3.6亿网格，完成了非定常状态效率测试及非定常分离过程的湍流流场计算，在in-house集群上12 288核并行效率达到90%（以768核为基准），在天河2号上12 288核并行效率达到70%（以384核为基准），数值模拟结果与试验结果符合良好。最后，在in-house集群上采用28.8亿非结构重叠网格进行了4.9万核的并行效率测试，结果显示，4.9万核并行效率达到55.3%（以4 096核为基准）。