飞行参数对导弹发动机羽流的影响

对导弹发动机在不同飞行条件下的羽流进行数值模拟,得到飞行参数对导弹发动机羽流的影响规律,为载机挂点设计和制定发射边界提供了相应的理论依据。计算结果表明,在相同飞行马赫数下随飞行高度的增加,导弹羽流边界随之增加：在相同飞行高度下随飞行马赫数的增加,导弹羽流边界随之减小,同时导弹羽流结构也随飞行奈件变化而有很大的不同。数值模拟与地面试验结果一致,计算具有较高的可信度。     

双级轴向涡流器文氏管长度对流场和喷雾特性影响

为了研究双级轴向涡流器文氏管长度对流场和喷雾特性的影响,通过数值计算和试验分别研究了4种文氏管长度的双级轴向涡流器方案的下游流场和匹配喷嘴的雾化特性。结果表明:随着文氏管无量纲长度由0.23增加至0.49,一级涡流器流量系数由0.98降至0.7,二级涡流器的流量系数保持0.75不变,涡流器出口旋流数由0.08增至0.48,旋流扩张角由闭合状态增至约90°,涡流器下游流场由反转回流区变为传统回流区。文氏管长度最短的方案的索太尔平均直径(SMD)和喷雾锥角受涡流器压降的影响较小,而其他方案的SMD和喷雾锥角受涡流器压降影响较大,且在相同涡流器压降和油压下,SMD和喷雾锥角随着文氏管长度增加而增大。      

双层壁冷却结构中多排射流冲击冷却的换热和流阻特性

采用稳态热敏液晶技术对双层壁冷却结构中的多排（包括顺排和叉排）射流冲击冷却结构进行了风洞实验,同时结合数值模拟的方法,对两种射流冲击冷却结构的传热和流阻特性的差异进行了研究。实验结果表明:流量系数和冲击靶板上的努塞尔数均随着雷诺数的增大而增大,而冲击孔的排布方式对面平均努塞尔数的影响较小,但是叉排结构的流量系数高于顺排结构,且冲击靶板上换热更加均匀。数值结果显示冲击靶板中心区域的流量分配和换热均随着冲击距离的增大而增大;而在下游区域内恰好与之相反。      

基于EMT采用FEM研究含裂纹介质中弹性波传播机制

了解和掌握弹性波在含有裂纹介质中的传播规律是开发利用页岩气等非常规油气资源中的关键科学问题.本文基于数值模拟的优点,采用商用有限元软件Nastran模拟弹性波在含裂纹介质中的激发及传播方式,分析了弹性波在该介质中裂纹微结构(密度和纵横比)对弹性波传播动力学特性的依赖程度.结果表明:有限元方法(FEM)可以用于该问题的研究;Hudson等效介质理论(EMT)不适用泊松比近0.5的材料;裂纹密度、纵横比的增大会减小纵波(P波)波速值,以及衰减位移时域响应的首波振幅,且裂纹密度对于该材料的各向异性的影响要远大于纵横比的作用.      

基于经验模态分解的地球同步轨道高能电子通量预报

在磁暴恢复相期间,大量相对论(高能)电子从磁层的外辐射带渗透到地球同步轨道区.其中> 2 MeV的高能电子能够穿透卫星表面并聚积在材料内部,导致卫星无法正常运行或完全损坏.磁暴期间的高能电子通量变化的非平稳与非线性特征十分明显.通过实验发现,经验模态分解法能够极大地降低高能电子通量非平稳性问题造成的预报影响.以2008-2009年的数据作为训练集,2010-2013年数据作为测试集.结果表明:2010-2013年的预报率约为0.84;在太阳活动较为复杂的2013年,预报率达到0.81.引入经验模态分解后预报效率得到显著提高.     

On the practical exploitation of perturbative effects in low Earth orbit for space debris mitigation

This paper presents the results of a numerical evaluation of the natural lifetime reduction in low Earth orbit, due to dynamical perturbations. The study considers two values for the area-to-mass ratio, a nominal ratio which resembles a typical value of spacecraft in orbit today, and an enhanced ratio which covers the surface augmentation. The results were obtained with two orbit propagators, one of a semi-analytical nature and the second one using non-averaged equations of motion. The simulations for both propagators were set up similarly to allow comparison. They both use the solar radiation pressure and the secular terms of the geopotential ($J_2,J_4$ and $J_6$). The atmospheric drag was turned on and off in both propagators to alternatively study the eccentricity build up and the residual lifetime. The non-averaging case also covers a validation with the full 6?×?6 geopotential. The results confirm the findings in previous publications, that is, the possibility for de-orbiting from altitudes above the residual atmosphere if a solar sail is deployed at the end-of-life, due to the combined effect of solar radiation pressure and the oblateness of the Earth. At near polar inclinations, shadowing effects can be exploited to the same end. The results obtained with the full, non-averaging propagator revealed additional de-orbiting corridors associated with solar radiation pressure which were not found by previous work on space debris mitigation. The results of both tools are compared for specific initial conditions. For nominal values of area-to-mass ratio, instead, it is confirmed that this resonance effect is negligible.The paper then puts the findings in the perspective of the current satellite catalogue. It identifies space missions which are currently close to a resonance corridor and shows the orbit evolution within the resonances with a significantly shorter residual orbital lifetime. The paper finishes with a discussion on the exploitation of these effects with regards to the long-term simulation of the space debris environment and a flux and collision probability comparison.     

高超声速飞行器无在线求导backstepping控制方法

针对高超声速飞行器纵向通道跟踪控制问题,提出一种无需对虚拟控制量进行在线求导的新型backstepping控制方法.首先将飞行器动力学模型划分为速度子系统和航迹倾角子系统,然后采用backstepping方法设计航迹倾角子系统控制器,利用高阶微分器技术直接设计虚拟控制量一阶导数的控制律,这样即避免了现有backstep...     

Dynamic temperature prediction of electronic equipment under high altitude long endurance conditions

Unmanned Aerial Vehicle (UAV) is developing towards the direction of High Altitude Long Endurance (HALE). This will have an important influence on the stability of its airborne electronic equipment using passive thermal management. In this paper, a multi-node transient thermal model for airborne electronic equipment is set up based on the thermal network method to predict their dynamic temperature responses under high altitude and long flight time conditions. Some relevant factors are considered into this temperature prediction model including flight environment, radiation, convection, heat conduction, etc. An experimental chamber simulating a high altitude flight environment was set up to survey the dynamic thermal responses of airborne electronic equipment in a UAV. According to the experimental measurement results, the multi-node transient thermal model is verified without consideration of the effects of flight speed. Then, a modified way about outside flight speed is added into the model to improve the temperature prediction performance. Finally, the corresponding simulation code is developed based on the proposed model. It can realize the dynamic temperature prediction of airborne electronic equipment under HALE conditions.     

KNi10真空钎焊ODS高温合金MGH956组织和性能研究

针对新型ODS高温合金MGH956开展钎焊工艺研究,采用自制钎料KNi10对该材料进行了系统的工艺研究。在焊缝间隙20μm、1240℃/10min的工艺参数下,实现了接头1000℃高温拉伸强度达到母材的90%左右。