防热试验用高温超声速燃气流场热环境分析

对用于防热系统试验考核的高温超声速燃气流场的流场结构和热环境特性进行了计算和分析.将CFD模拟方法与工程计算方法相结合,对两类锥形喷管形成的燃气流场进行了数值模拟计算和流场结构分析,并与试验过程中高速拍摄的图片进行了比对.利用模拟得到的流场气动参数,计算了沿流场轴向位置球头驻点模型的热流和压力,并与试验测量数据进行了对比,结果吻合较好.锥形喷管形成压缩波和膨胀波交替的流场结构,导致流场气动参数与模型热流和压力形成正弦变化的特点.     

轻质防热材料高焓烧蚀试验

为了得到不同轻质防热材料在高焓条件下的烧蚀数据,评估其在高焓条件下的烧蚀性能,以满足

未来高超声速飞行器再入的高焓高热流低压力的热环境,采用高焓加热器对多种不同密度的轻质防热材料进

行烧蚀考核试验。通过对试验数据和模型内部烧蚀形态的描述,给出轻质防热材料在高焓低压热环境中的烧

蚀特性。最后对比中焓条件下试验数据,详细分析焓值对轻质防热材料烧蚀性能的影响。结果显示,高焓加热

器可以产生稳定均匀的高焓低压流场,轻质防热材料在高焓条件下的隔热性能和烧蚀性能有所提高。

     

高精度A/D转换技术在惯导系统中的应用研究

针对惯导系统对模数转换电路的使用要求,明确了制约A/D转换电路在惯导系统中应用的瓶颈是零位稳定性,分析了A/D转换电路零位的影响因素,提出了解决方法。并设计出一款A/D转换电路,该电路的测试结果表明解决方法有效,可将零位提高2个数量级,与传统V/F转换电路相当。证明采用A/D转换芯片的模数转换电路能够满足惯导系统的精度要求,同时相比V/F、I/F具有高采样率和高分辨率的优势,技术指标可以满足高精度加速度测量系统等实际工程需求。     

运输机机翼、机身和翼身组合体气动特性雷诺数效应的数值模拟研究

通过CFD方法对运输机单独机身、翼身组合体及不同厚度和弯度的翼型进行了数值模拟研究,分析了雷诺数对机身和翼身组合体气动特性的影响规律,通过雷诺数对有弯度的翼型及旋成体气动特性影响的研究,初步解释了雷诺数对机身和机翼影响差别的原因。     

脉冲爆震火箭发动机高频实验研究

为了研究脉冲爆震发动机的高频工作特性,以航空煤油和压缩氧气为推进剂,采用爆震增强装置,增大推进剂供给压力以及增大电磁阀控制气压力等措施,在脉冲爆震火箭发动机模型上进行了实验,成功获得45Hz时的爆震压力波形。实验结果表明,频率增高,爆震波峰值压力下降,有利于加速缓燃向爆震的转变(Defla-gration to Detonation Transition,DDT)。当爆震充分发展时,爆震波波速基本不变,峰值压力上升时间趋于定值。工作频率为45 Hz时,爆震波峰值的压力为3.2 MPa,爆震波的波速为1 715.5m/s。     

Trailing-edge scalloping effect on flat-plate membrane wing performance

This investigation studies the effect of trailing-edge scalloping on the lift and drag force coefficients of flat, membrane wings that vibrate at low Reynolds numbers (<61,000). A series of rigid, flat plate frames with moderate aspect ratio and repeating membrane cell structure were studied and compared to a rigid plate and a rigid scalloped plate. Lift and drag measurements were acquired using an external force-balance; flow fluctuation measurements were captured with a hot-wire. Results showed that the size and aspect ratio of the latex cell had a greater impact on lift than scalloping and that scalloping had a greater effect on drag than the cell aspect ratio. Compared to the solid wings, the membrane wings exhibited higher lift and drag coefficients, likely due to both effective cambering and dynamic interaction with the free shear layer. While trailing-edge scalloping decreased both the lift and drag coefficients relative to no scalloping, the greater effect was on drag, thus, increasing aerodynamic efficiency. The maximum lift-to-drag ratio was attained for a 25% scallop with a repeating cell aspect ratio of one. A unique nondimensional scaling of the membrane vibration peak frequency is also presented.     

Ionospheric heating due to solar flares as measured by SROSS-C2 satellite

The data on thermal fluctuations of the topside ionosphere have been measured by Retarding Potential Analyser (RPA) payload aboard the SROSS-C2 satellite over the Indian region for half of the solar cycle (1995–2000). The data on solar flare has been obtained from National Geophysical Data Center (NGDC) Boulder, Colorado (USA) and other solar indices (solar radio flux and sunspot number) were download from NGDC website. The ionospheric electron and ion temperatures show a consistent enhancement during the solar flares. The enhancement in the electron temperature is 28–92% and for ion temperature it is 18–39% compared to the normal day’s average temperature. The enhancement of ionospheric temperatures due to solar flares is correlated with the variation of sunspot and solar radio flux (F10.7cm). All the events studied in the present paper fall in the category of subflare with almost same intensity. The ionospheric electron and ion temperatures enhancement have been compared with the IRI model values.     

烧蚀材料的多光谱真温测量法

应用棱镜分光式多波长光电高温计对氧乙炔焰烧蚀材料的真实温度进行了测量。精心地选择波段及处理方法使烧蚀材料剥离、水蒸汽及烟雾影响减至最小，采用一点标定技术解决了高温区标定问题。     

对高温低周疲劳寿命预测模型的评价

高温低周劳寿命预测方法对于承受变幅载荷的高温构件的设计具有重要意义。本文系统介绍了迄今这方面所取得的研究成果，特别对目前在国内外影响较大的ＳＲＰ等几个ＨＬＦ寿命预测的经典参数模型和近些年发展起来的预测ＨＬＦ寿命的损伤力学方法作了较为详细的评价，并指出存在问题和研究方向。     

连续分离铝熔体中夹杂物的分析

通过分析高频磁场作用下熔体连续处理时夹杂的去除效率表明，熔体连续处理条件下的夹杂去除效率比熔体静止时的略低，而夹杂与熔体之间的密度差对电磁分离时的去除效率影响不大。提高去除效率的有效途径是增大磁感应强度或降低分离器管径，但减小管径的同时需要提高磁场频率，以保持α/δ的值在2附近才可以取得最佳的分离效果。