行星际空间MHD模拟激波跃变关系分析

分析了模拟得到的可以传播到1AU以远的日地空间磁流体力学激波与Rankine-Hugnoniot跃变关系的符合程度．通过对模拟激波的结构及其在传播过程中的演化进行的分析，提出了模拟激波的定位方法；基于所提出的定位方法，利用向长青提出的确定MHD激波局地参数的方法计算了模拟得到的激波与Rankine-Hugnoniot跃变关系的偏差．结果表明在激波传播到100Rs以后，激波对中前向快激波与Rankine-Hugnoniot关系的符合达到很高的程度，相对误差在10^-2数量级以内；并且在激波传播到150 Rs以后，相对误差在10^-3数量级以内．这个结果说明文中所使用的有限差分数值格式能较好地模拟激波．     

Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

双层壳型涡轮叶片中冲击旋流换热增益效果试验

以双层壳型涡轮叶片内冷通道中旋流换热特性为研究对象,采用热膜法,对双层壳型冷却结构中的狭小受限通道中,旋流作用下换热特性的变化规律开展了细致的试验研究。重点分析了冷却空气的旋流作用对换热的强化增益效果。试验中通过改变冲击Re数(10 000～20 000),冲击间距和冲击孔直径之比H/D(0.35～1.7)等参数,研究了其对旋流的形成及内表面局部换热系数的影响规律。研究发现:由于双层壳型叶片内冷通道的空间受限,冷却空气在通道内形成了旋流结构,该旋流结构显著影响了内表面的局部换热系数并可以有效提高换热效果。研究结果表明:内表面局部换热系数对冲击间距和冲击孔直径之比H/D最为敏感,对于不同冲击Re数,存在一个最佳的H/D使得旋流换热增益效果达到最大(Re=10 000时,最佳H/D为0.95;Re=15 000,20 000,最佳H/D=0.63)。     

基于激波控制的流体推力矢量喷管试验

以二元收扩喷管为对象,开展了基于二次流喷射的流体推力矢量技术研究。基于试验研究,得到了不同喷管落压比、不同的二次流总压比和不同的二次流喷射角度多种工况下的喷管上下壁面中心线压力分布规律以及喷管壁面油流分布图。通过对不同工况下参数变化规律分析,给出了基于二次流喷射的流体推力矢量喷管的主次流气动参数及几何参数对流体推力矢量喷管流场结构和性能影响的关联关系。从试验和分析结果可以看出,喷管落压比、二次流总压比和二次流喷射角度等喷管的主次流气动几何参数对基于流体推力矢量喷管参数变化有明显的影响。     

非对称来流下隔离段动态压力特性

为了探讨非对称来流下矩形隔离段内动态压力特性,用直联实验方式以及动态压力测量技术进行了试验,并用统计分析方法分析了数据。实验结果表明,入口来流的非对称性对上下壁面压力脉动大小以及传播平均速度有较大影响,而对频率无多大影响。激波串区域内壁面压力脉动向下游传播比向上游传播衰减得快。在隔离段出口超声速条件下,观测到的压力脉动频率主要在70 Hz以下,而在出口亚声速条件时,压力脉动的频率不仅有70Hz以下的部分,而且还有100~200 Hz之间的部分。     

超声速进气道喉部附面层抽吸

为研究超声速进气道喉部之后流场激波附面层干扰,采用FLUENT软件模拟了单楔角进气道在设计工况下流动情况。通过分析,提出进气道喉部抽吸。计算了三种抽吸缝大小下进气道喉部之后流场,计算结果表明,喉部抽吸能使激波稳定于喉部,通过抽吸能改善喉部之后流场状况,提高进气道性能,少量抽气不改变流场结构,加大抽气量,使喉部之后激波串转变成正激波,正激波之后流场不分离,进气道出口性能参数提高显著。     

几种超声速非常规压缩系统的研究

根据斜激波和膨胀波理论,数值计算得到给定非常规压缩型面所形成的弯曲激波型面和壁面静压分布,同Fluent计算结果进行比较。应用Fluent软件,计算了等压力梯度设计非常规曲面压缩二元进气道、常规等熵压缩二元进气道和三楔压缩二元进气道设计点性能。研究结果表明:数值计算得到的弯曲激波型面与Fluent计算结果吻合较好。等压力梯度设计的非常规压缩型面壁面静压均匀上升,有利于防止壁面附面层分离;其压缩面长度比等熵压缩面缩短21.6%,减轻了进气道的重量。