新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响

通过金相观察(OM)、扫描电镜(SEM)以及拉伸测试系统地表征和研究了热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响。研究表明:固溶态GW94、GW74、GW44合金主要由α-Mg过饱和固溶体、铸态残留相Mg5(Gd,Y)以及固溶过程形成的方块相组成。随着Gd含量的增加,固溶态Mg-Gd-Y合金中方块相的体积分数不断增加;在同一时效温度下,合金达到时效峰值的时效时间缩短;室温下拉伸的固溶态、时效峰值态合金以及200和250℃下拉伸的时效峰值态合金的抗拉强度和屈服强度不断提高(固溶态合金屈服强度先降低后升高),但是伸长率却是不断降低。时效峰值态GW94合金表现出优越的力学性能,室温时其抗拉强度和屈服强度分别为300、247 MPa,而伸长率仅为0.9%;200和250℃拉伸时,时效峰值态GW94合金抗拉强度、屈服强度和伸长率分别为329、234 MPa和2.6%以及312、233 MPa和2.7%。时效峰值态GW94、GW74合金出现抗拉强度随温度升高而升高的反常力学行为。     

不同环境因素对引压管腔动态特性影响

为了探索引压管腔在动态压力校准和使用中不同环境因素对动态特性的影响,推导了管腔传压模型和谐振频率关系式,确立了影响管腔动态特性的参数,包括静态压力、温度、气体介质等。采用引压管腔专用实验装置进行了不同环境参数状态的实验验证,结果表明:静态压力仅会影响管腔在谐振频率附近的输出,随着静态压力的增大而非线性增大,对动态特性并无明显改变;温度会改变管腔的谐振频率和动态特性,随着温度的升高,谐振频率增大但输出幅值随之减小;气体介质的不同会彻底改变管腔动态特性,主要取决于介质的声速。该研究为引压管腔在使用环境下数据的评价和数据修正上提供了一定参考依据。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

瞬变流速作用下姿控发动机燃料管路的非线性振动特性分析

为研究瞬变流速激励下某型卫星姿控发动机燃料输送管路的非线性振动特性,采用加权余量法和四阶Runge—Kutta法对燃料输送管路的非线性液固耦合振动模型进行了数值仿真,研究不同燃料流速下、电磁阀开关时长对燃料管路非线性振动稳定性的影响.仿真结果表明,依据管路特征线可将管路振动分为稳定振动区和不稳定振动区,且不稳定振动主要...     

连续突变管道流动局部水头损失建模研究

管道系统中设置的阀门、限流环等十分常见,装备限流装置的管道本质就是典型的连续突变管道。突变管道流动存在十分明显的局部水头损失,因此工程设计人员在进行管道系统设计时不得不考虑因管道突变而产生的局部水头损失;目前针对单个突变管道流动局部水头损失已有较为深入的研究,并已推导出相应的计算模型,但对于连续突变管路的水头损失研究较少,工程设计中对于连续突变管路的局部水头损失计算采用基于单个突变管道水头损失的叠加计算法,由于连续突变管路流动为极其复杂的湍流,基于单个突变管道水头损失的叠加计算法而得到的连续突变管路的局部水头损失结果误差较大。鉴于此,采用理论推导与实验相结合的方法,设计四种不同管径比的管道以及23种不同进口流量工况,并以航空煤油为介质进行实验,利用实验结果进行分析并对传统的突变管道水头损失的叠加计算法进行修正,提出了连续突缩突扩管道的局部水头损失修正计算模型,其计算结果相比于传统计算方法在精度上得到了显著性提高,为工程管道系统设计中的连续突变管路局部水头损失计算提供了有力依据。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。