Modeling the effects of green alternative on heat island mitigation of a meso level town,West Bengal,India

Urban heat island (UHI) is emerged as a ubiquitous phenomenon that affects the outdoor thermal comfort. Hence urban microclimatic studies using numeric simulation software to find out adaption strategies are attracting the great attention of researchers and policymaker. Number of scientists carried out their research on this topic using different tools and technique whereas ENVI-met model is the most widely used simulation tools. The present study intended to examine the implication of green infrastructure of the town on enhanced microclimatic condition and to evaluate the best suitable mitigation strategy modelling cool city with ENVI-met software (V4). Five greening condition such as existing UHI condition (C1), 100% greening of roof (C2), 100% greening of roof and walls (C3), 50% greening of roof and walls (C4) and: Plantation at suitable area with 50% greening of roof and walls (C5) have been taken into consideration for the microclimate simulation for all three selected sites. Among these five conditions, C3 for the open mid-rise and compact low-rise, C5 for the open low-rise are identified as one of the most suitable strategies which can reduce the air temperature of peak hours by 2.6 °C, 1.33 °C and 1.87 °C respectively. These models are validated by simple linear regression between simulated and existing air temperature in case of existing UHI condition (C1) and in all the cases coefficient of determination value is high such as for open mid-rise, compact low-rise and open low-rise, it is 0.92, 0.92 and 0.75 respectively. Therefore it can be concluded that the application of those strategies can improve the urban thermal environment as well as the outdoor thermal comfort of English bazaar Town and its surroundings.     

关于对喷水室热工计算公式的分析及修正

通过分析喷水室内水和空气之间的热质交换过程，指出目前采用的热工计算公式的不足，并在此基础上推导出喷水室热平衡方程新公式，对理论教学起到一定的指导作用。     

刚性隔热瓦重复使用性评价研究

为满足未来新型飞行器对隔热材料的需求,将刚性隔热瓦在1 200℃热处理30 min,对其质量稳定性、尺寸稳定性、力学性能、隔热性能以及微观结构等进行了评价.结果表明,热处理20次的质量损失率、xy向线性收缩率、隔热性能以及微观结构变化都很小,仅z向线性收缩率稍大(3.19％).综合来看,1 200℃/30min的使用条件下,隔热瓦能够满足20次的重复使用要求.     

固体微推力器设计与数值分析

设计了两种基于微光机电技术的固体微推力器结构,其中一种结构具有不连续的非正常拉瓦尔喷管。采用数值计算方法对不同的设计进行了内弹道、燃气流动过程和热损失的数值分析。结果表明:不连续的非正常拉瓦尔喷管同样能够将推进剂燃气加速到超声速,其比冲性能与正常拉瓦尔喷管相当;微光机电技术常用的硅材料会造成推力器比冲性能较大量级的下降,而绝热性能良好的玻璃或陶瓷材料可以有效提高微推力器的比冲性能。     

热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响

通过金相观察(OM)、扫描电镜(SEM)以及拉伸测试系统地表征和研究了热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响。研究表明:固溶态GW94、GW74、GW44合金主要由α-Mg过饱和固溶体、铸态残留相Mg5(Gd,Y)以及固溶过程形成的方块相组成。随着Gd含量的增加,固溶态Mg-Gd-Y合金中方块相的体积分数不断增加;在同一时效温度下,合金达到时效峰值的时效时间缩短;室温下拉伸的固溶态、时效峰值态合金以及200和250℃下拉伸的时效峰值态合金的抗拉强度和屈服强度不断提高(固溶态合金屈服强度先降低后升高),但是伸长率却是不断降低。时效峰值态GW94合金表现出优越的力学性能,室温时其抗拉强度和屈服强度分别为300、247 MPa,而伸长率仅为0.9%;200和250℃拉伸时,时效峰值态GW94合金抗拉强度、屈服强度和伸长率分别为329、234 MPa和2.6%以及312、233 MPa和2.7%。时效峰值态GW94、GW74合金出现抗拉强度随温度升高而升高的反常力学行为。     

热力系统中分布参数对象的数值─解析混合仿真方法

以热力系统中常见的管式换热器为对象，建立了包括质量、动量和能量平衡方程的集中参数数学模型，通过一系列的数值简化和处理，获得了能量方程的解析解，并发现此解的精度对时间步长的大小不很敏感。利用这一特性，本文提出了数值—解析混合仿真方法，采用多段集中参数模型同时选用较大的时间步长进行仿真。与非线性分布参数模型计算结果的对比表明，本仿真方法不仅具有较高的精度，同时也大大提高了计算速度，实现了仿真精度和实时性的统一。本方法对热力系统中分布参数对象的仿真具有重要意义。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operati...     

吸热型碳氢燃料热沉的测定

介绍了一套自制的热导式高温量热系统,热量常数可用电标定法测定。用此仪器可测定各种吸热型碳氢燃料在各种条件下的热沉,用于吸热型碳氢燃料的筛选,为吸热型碳氢燃料的研究提供可靠的热化学数据。用这套装置测定了两种吸热型碳氢燃料在７００°Ｃ的热沉,与文献值接近。     

多层喷射沉积制备大尺寸耐热铝合金管坯的研究

采用多层喷射沉积工艺制备出了尺寸为Ф630 mm×250 mm×800 mm且质量较好的FVS0812耐热铝合金管坯,通过挤压获得了性能优良的大直径管材,并对管坯和挤压后管材的力学性能和微观结构进行了检测和分析.分析结果表明,多层喷射沉积制坯过程中,熔滴在沉积面的冷却速度约3.2×104 K@s-1～106K@s-1,熔滴凝固后在沉积坯中形成微细晶粒结构(200 nm～500 nm)和弥散分布的纳米析出相Al12(Fe,V)3Si(20nm～60 nm),使得沉积坯挤压致密后具有优异的性能.     

考虑气体扩散渗透的隔热材料瞬态隔热性能数值模拟

高超声速飞行器机动飞行时环境压力变化导致隔热材料沿厚度方向存在压力梯度,进而引起隔
热材料内气体的扩散渗透,影响隔热材料隔热性能。为研究气体扩散渗透对隔热材料隔热性能的影响,建立了
隔热材料内气体扩散渗透模型,采用罗斯兰德近似、有限体积法建立了隔热材料内扩散渗透及辐射导热传热计
算模型,对气体扩散渗透条件下的瞬态隔热性能进行了数值模拟。算例模拟结果表明:对2 cm 厚纳米隔热材
料,在外界气压为0. 1 MPa,绝热面为真空的状况下,当渗透率大于10-14 m2 时,气体扩散渗透开始影响隔热材
料内传热,导致隔热性能降低,气体黏性系数对气体扩散渗透有显著影响,随着黏性系数降低,气体扩散渗流现
象显著;衰减系数对绝热面温度响应有显著影响,随着衰减系数增大,绝热面温度响应显著降低。