新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响

通过金相观察(OM)、扫描电镜(SEM)以及拉伸测试系统地表征和研究了热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响。研究表明:固溶态GW94、GW74、GW44合金主要由α-Mg过饱和固溶体、铸态残留相Mg5(Gd,Y)以及固溶过程形成的方块相组成。随着Gd含量的增加,固溶态Mg-Gd-Y合金中方块相的体积分数不断增加;在同一时效温度下,合金达到时效峰值的时效时间缩短;室温下拉伸的固溶态、时效峰值态合金以及200和250℃下拉伸的时效峰值态合金的抗拉强度和屈服强度不断提高(固溶态合金屈服强度先降低后升高),但是伸长率却是不断降低。时效峰值态GW94合金表现出优越的力学性能,室温时其抗拉强度和屈服强度分别为300、247 MPa,而伸长率仅为0.9%;200和250℃拉伸时,时效峰值态GW94合金抗拉强度、屈服强度和伸长率分别为329、234 MPa和2.6%以及312、233 MPa和2.7%。时效峰值态GW94、GW74合金出现抗拉强度随温度升高而升高的反常力学行为。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

双层壳型涡轮叶片中冲击旋流换热增益效果试验

以双层壳型涡轮叶片内冷通道中旋流换热特性为研究对象,采用热膜法,对双层壳型冷却结构中的狭小受限通道中,旋流作用下换热特性的变化规律开展了细致的试验研究。重点分析了冷却空气的旋流作用对换热的强化增益效果。试验中通过改变冲击Re数(10 000～20 000),冲击间距和冲击孔直径之比H/D(0.35～1.7)等参数,研究了其对旋流的形成及内表面局部换热系数的影响规律。研究发现:由于双层壳型叶片内冷通道的空间受限,冷却空气在通道内形成了旋流结构,该旋流结构显著影响了内表面的局部换热系数并可以有效提高换热效果。研究结果表明:内表面局部换热系数对冲击间距和冲击孔直径之比H/D最为敏感,对于不同冲击Re数,存在一个最佳的H/D使得旋流换热增益效果达到最大(Re=10 000时,最佳H/D为0.95;Re=15 000,20 000,最佳H/D=0.63)。     

HTPB推进剂湿热老化规律及损伤模式实验

通过HTPB推进剂湿热老化实验,采用测定单轴定速拉伸条件下标准哑铃形试件声发射(AE)信号的方法,结合扫描电镜(SEM)断面观察结果,对HTPB推进剂的湿热老化规律和损伤模式进行了研究,给出了一个描述湿热老化性能变化规律的三阶段模型。实验研究表明:声发射信号累积计数对时间的导数的大小对应基体开裂、脱湿和宏观断裂三种损伤模式;同时水份破坏粘合剂和氧化剂的界面是导致脱湿关键因素,且水份在推进剂中的浓度与脱湿严重程度呈正相关。     

高温处理对中密度针刺C/C复合材料性能的影响

针对C/C复合材料脆性问题,对密度为1.60 g/cm3的碳布叠层针刺C/C复合材料进行了1800、2 000、2 200和2 500℃的高温处理,研究了不同热处理温度对C/C复合材料微晶结构、力学和抗热震等性能的影响.结果表明,高温处理使针刺C/C复合材料的层间剪切和面内拉伸强度出现不同程度的降低,但材料的断裂伸长率和抗热震性能得到大幅度提高.其中,1 800℃高温处理后的C/C复合材料具有优异的力学和抗热震性能.     

冲压发动机气膜冷却分析模型

本文建立了冲压发动机燃烧室气膜冷却传热分析程序。根据燃烧室设计的技术要求,从冷却性能角度完成气膜冷却系统的气动性能和传热特性分析,提供冷却结构优化所需的信息。     

粉末耐热钛合金组织性能及成形技术

采用热等静压技术及旋转电极粉,采用预合金粉粉末冶金工艺开展了粉末耐热钛合金TC11(Ti-6.5AJ-3.5Mo-1.5Zr-0.3Si)制备技术研究,研制出了全致密粉末TC11合金,通过热处理工艺研究优化粉末TC11材料的组织和性能.利用光学显微镜,对其组织进行了分析,用SEM观察了旋转电极粉末形貌,对室温及高温(550℃)拉伸性能及弹性模量等进行了测试分析.粉末TC11合金的组织和性能与同批次TC11锻棒材料进行了对比研究.利用特殊模具成形,开展了粉末TC11构件近净成形技术的研究,实现了整体大尺寸、带网格加强筋的薄壁粉末TC11合金航天飞行器舱体件近净成形,且未检测出内部缺陷.研究结果表明,粉末TC11合金具有与锻造材料相当的拉伸性能,而弹性模量更优,其金相组织均匀细致,形成了网篮组织,并有围绕其分布的等轴α.粉末TC11合金及合适的近净成形技术可在高性价比、高可靠性的轻质耐热航天飞行器构件制备中得到应用.