An extended chirp scaling algorithm for spaceborne sliding spotlight synthetic aperture radar imaging

A system impulse response with low sidelobes is critical in synthetic aperture radar（SAR） images because sidelobes contribute to noise and interfere with nearby scatterers. However,the conventional tricks of sidelobe suppression are unable to be exactly applied to the case of spaceborne sliding spotlight SAR due to great azimuth shifts in both time and frequency domains. In this paper, an extended chirp scaling algorithm is presented for spaceborne sliding spotlight SAR data imaging. The proposed algorithm firstly uses the spectral analysis（SPECAN） technique to avoid the azimuth spectrum folding effect and then employs the chirp scaling（CS） algorithm to achieve data focusing, i.e., the so-called two-step approach. To suppress the sidelobe level, an efficient strategy for the azimuth spectral weighting which only involves matrix multiplications and short fast Fourier transformations（FFTs） is proposed, which is a post-process executed on the focused SAR image and particularly simple to be implemented. The SAR image processed by the proposed extended CS algorithm is very precise and perfectly phase-preserving. In the end, computer simulation results verify the analysis and confirm the validity of the proposed algorithm.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

民机防冰系统自然结冰试飞技术研究

结合某型民机自然结冰条件下防冰系统的试飞,对试飞所需的测试改装工作进行了总结,并对试飞前需进行的各种安全性评估进行了总结说明,明确了试飞中需考虑的各种构型情况,提出一套循序渐进的自然结冰试飞方法。同时提出了试飞中结冰气象参数的可接受性判据,最后针对自然结冰试飞中结冰气象参数的处理提出了分段等效处理的方法。     

浅析运输类飞机经济舱头排旅客座椅头部损伤判据的影响因素

介绍了头部损伤判据HIC的概念、适航要求及影响运输类飞机客舱头排旅客座椅HIC的相关参数;叙述了旅客座椅头排距、头部撞击壁板的刚度、安全带织带伸长率、乘坐摩擦系数等参数的影响和重要程度;对如何设计符合HIC要求的经济舱头排旅客座椅和壁板提出了建议。     

民用飞机综合模块化航电系统分区和资源分配的研究

对比航电传统系统架构,分析了综合模块化航电系统(Integrated Modular Avionics,简称IMA)架构的优点;针对IMA系统功能的高集成度带来的资源分配难度和安全性要求,提出了IMA系统分区和资源分配策略,并给出了具体方法,对民用飞机IMA系统设计具有一定的指导意义和实用价值。     

基于A320飞机横航向控制律架构的LQ设计

空客A320飞机横航向控制律采用特征结构配置方法计算闭环增益,实现了期望特征值的配置及横航向关键参数之间的解耦。基于A320横航向控制律架构,提出使用线性二次型(Linear Quadratic,简称LQ)方法,对闭环增益进行重新设计。首先根据期望的特征值引入关键参数的频域整形环节,而后通过调整二次型性能指标加权矩阵实现期望特征值的逼近及关键参数之间的解耦,并求得闭环反馈增益,最后在特征结构、稳定裕度和横航向解耦效果方面与空客设计结果作了对比分析。仿真结果表明,LQ设计可获得与特征结构配置设计相近的结果,即得到接近期望值的特征值,并实现关键变量的解耦,同时保证了闭环稳定裕度。     

微小推力下小卫星的轨道递推与推力标定

针对采用微小推力进行轨道机动的小卫星,考虑复杂摄动力的基础设计了一种高精度轨道外推和推力在轨标定算法.首先,建立了考虑地球复杂摄动力和微小推力的小卫星轨道动力学模型;然后基于动力学模型,利用变步长龙格库塔算法,设计了对微小推力小卫星进行高精度轨道外推的方法.随后通过无迹卡尔曼滤波器(UKF),设计在轨标定算法,对存在误...     

电离层顶部电子含量对GNSS电离层层析的影响分析

卫星信号射线上的总电子含量(slant total electron content, STEC)是像素基全球卫星导航系统电离层层析(computerized ionospheric tomography, CIT)建模的必要数据来源，但电离层层析通常忽略1 000 km以上的顶部电子含量，为弄清这部分电子含量对层析结果的影响，利用NeQuick2模型计算站星视线上的STEC与其在电离层区域内的STEC比值来改正原始数据，并分别利用改正前后的STEC进行电离层层析。结果显示，电离层顶部电子含量占比约为10%，白天占比略大于黑夜，与测高仪站的数据相比，改正后的均方根值比改正前提高了20%以上；与Swarm卫星提供的电子剖面数据对比，改正后的层析结果精度较改正前提升了19.6%左右，且该方法受地磁扰动影响较为明显。总的来说，利用CIT进行小尺度电离层探测，可较直观地看出，顶部电子含量对层析结果的影响较大，需要采取相应手段予以剔除。     

Noise analysis of continuous GPS coordinate time series for CMONOC

The Crustal Movement Observation Network of China (CMONOC) is one of the major scientific infrastructures, mainly using Global Positioning System (GPS) measurements, to monitor crustal deformation in the Chinese mainland. In this paper, decade-long coordinate time series of 26 continuous GPS sites of CMONOC are analyzed for their noise content using maximum likelihood estimation (MLE). We study the noise properties of continuous GPS time series of CMONOC for the unfiltered, filtered solutions and also the common mode signals in terms of power law plus white noise model. In the spatial filtering, we remove for every time series a common mode error that was estimated from a modified stacking of position residuals from other sites within ∼1000 km of the selected site. We find that the common mode signal in our network has a combination of spatially correlated flicker noise and a common white noise with large spatial extent. We demonstrate that for the unfiltered solutions of CMONOC continuous GPS sites the main colored noise is a flicker process, with a mean spectral index of ∼1. For the filtered solutions, the main colored noise is a general power law process, indicating that a major number of the filtered regional solutions have a combination of noise sources or local effects. The velocity uncertainties from CMONOC continuous GPS coordinate time series may be underestimated by factors of 8–16 if a pure white noise model is assumed. In addition, using a white plus flicker noise model, the median values of velocity errors for the unfiltered solutions are 0.16 (north), 0.17 (east) and 0.58 (vertical) mm/yr, and the median values for the filtered solutions are 0.09 (north), 0.10 (east) and 0.40 (vertical) mm/yr.     

CCD信号采样位置选取方法的研究

针对CCD输出信号中的复位噪声,文章介绍了处理复位噪声较为常用的方法--相关双采样技术,并对相关双采样技术中采样位置选取的方法进行分析和研究,最后进行了实验验证.结果表明:用文中方法选取的采样位置进行相关双采样,可以较好的减小CCD输出信号中复位噪声的影响,提高信噪比.