火箭发动机超声速过膨胀射流气动噪声特性研究

采用大涡模拟LES方法计算了火箭发动机超声速过膨胀射流形态及近场声压分布,研究了入口温度与环境温度的比值(温度比)对声场的影响;将声源分解,基于Ffowcs Williams-Hawkings (FW-H)方程获取了不同位置噪声源的远场噪声,并根据声压级频谱和湍流形态分析了超声速射流噪声的产生机理。研究表明,超声速过膨胀射流气动噪声由湍流混合噪声和宽频激波噪声组成,近场噪声源以马赫波形式向大方位角辐射中高频噪声,下游大尺度湍流向低方位角范围辐射低频噪声,声压级峰值频率随观测角度增大而升高;随温度比升高,马赫波辐射角度增大,噪声指向性发生改变。该研究可为运载火箭发动机地面试车或火箭发射段声学环境设计提供参考。     

高超飞行器表面热效应地面模拟实验研究

文章深入分析高超飞行器与临近空间大气相互作用的基本物理过程,激波加热及粒子碰撞产生等离子体的物理机制,并利用磁热屏蔽效应在高超飞行器模拟器与高速定向流间建立磁化等离子体鞘层,大幅降低中性激波气体向飞行器的能流传递,从而为高超飞行器提供有效的热防护作用。通过两次比对实验验证了磁热屏蔽效应的有效性及工程实施的可行性,为今后研制高韧性、超轻质、可重复使用热防护复合材料提供了实验数据,奠定了技术基础。实验中利用层流等离子体源作为高能流密度热源是热防护实验装备上的创新,层流等离子体源能流截面大、能流密度高,可以针对高超飞行器表面热效应进行全尺寸的模拟实验。     

光纤氢传感技术的研究现状及其应用前景

分析了光纤氢传感技术发展的现状和特点，比较了几种典型光纤氢传感器的结构和工作原理。指出了光纤氢传感技术是测量易爆环境下氢气浓度的有效方法，并对光纤氢传感技术的应用前景和有待解决的问题进行了讨论。     

幂律型流体射流破碎建模和实验问题探讨

简要回顾了射流破碎研究的现状,讨论了幂律型流体射流破碎建模和实验的相关问题。射流破碎建模的关键在于依据流体的胶凝结构和组份物性,射流与环境气体之间的作用关系,提炼主要影响因素。射流破碎实验研究的关键在于高分辨率和高速成像技术等光学测试技术。建模和实验的主要作用在于揭示射流破碎的机理,分析相关因素的影响,为喷注器雾化研究提供参考,为燃烧室冷却设计提供依据。     

螺旋桨目标的ISAR回波信号建模与分析

建立了一种螺旋桨回波散射点叠加模型（BSPS）。给出了基于逆合成孔径雷达（ISAR）成像的螺旋桨调制模型（IBJEM）。根据螺旋桨的ISAR回波特性,对三种有不同螺旋桨结构的桨叶回波进行了成像仿真,讨论了螺旋桨结构参数对桨叶回波特性的影响。研究结果表明：该模型有较大的实用价值。     

Numerical analysis of deflection control of a gas plasma jet based on magnetohydrodynamic staggered electrode configuration

To control the deflection of the gas plasma jet, a new analytical method is proposed based on the Magnetohydrodynamic(MHD) technique. Based on the typical MHD power generation model, the applied voltage is applied to the staggered electrodes, that is, a pair of electrodes on the same side wall are connected to generate an axial current in the channel. Under the action of the magnetic field perpendicular to the direction of the flow, the plasma is subjected to electromagnetic forces perpendicular...     

某型民航客机改公务机应急出口变更适航符合性分析

民航客机改公务机后客座数会大幅降低,原有的应急出口布置存在超出适航要求的可能。研究了某型民航客机改为公务机后,对应急出口设置进行变更的可行性,分析了应急出口变更后对CCAR25.807条款的适航符合性,为今后民航客机改为公务机应急出口设计提供理论支持。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

提高飞行器升力的若干方法研究

本研究用数值模拟方法研究了四种增升方法。数据模拟的出发方程是可压流的Ｎ－Ｓ方程，格式为Ｂｅａｍ－Ｗａｒｍｉｎｇ格式的改进型。通过上述方法分别研究了：（１）动界效应对提高升力的作用；（２）涡的有利干扰对主升力面的影响；（３）吸气的驻涡增效应；（４）升力面下表面向下喷气的增升作用。研究结果表明，采用上述四种方法可有效地提高飞行器的升力，对改善飞行器的性能有着十分重要的意义。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.