脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。     

双脉冲固体火箭发动机隔舱打开与破片运动过程模拟

相比传统固体火箭发动机,具有能量管理特性的双脉冲固体火箭发动机结构更为复杂,为了提高其工作可靠性,针对核心部件金属隔舱的破片运动过程开展了数值仿真与试验研究。首先基于LS-DYNA软件,分析中引入监测函数、逻辑开关函数和加载驱动函数,模拟燃气流对破片的连续作用力,计算得到了在不同时刻破片的空间分布规律、撞击点位置及发动机内部损伤情况,保证了破片运动过程的高保真还原。其次,为了验证仿真结果的准确性,进行了模拟二脉冲初始工况的热流试验,发现破片撞击位置及损伤程度的仿真结果与试验数据一致性较高,其中撞击位置的预示误差小于9%,试验结果充分验证了有限元模型的准确性。由此,建立了适用于双脉冲固体火箭发动机金属隔舱破片运动过程的分析模型,实现了破片撞击位置及损伤程度的高精度预示。     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。     

室火轰燃的大涡模拟

采用一套修正的适用于低马赫数浮力流的N-S方程组来描述火灾场,运用Smagorinsky亚格子模型的大涡模拟方法对室内池火的轰燃发展过程进行了数值模拟,把模拟与实验结果进行了对比和分析。结果表明,该方法能较好地预测轰燃。同时模拟结果显示火焰区向房间后部偏转稍大,近壁处温度预测的误差大一些,随着亚格子模型的不断完善和计算能力的提高,用该技术来预测轰燃现象会更加准确。     

外挂物投放问题的二维非结构动态网格技术研究

以动态网格守恒型方程为控制方程,在二维非结构网格基础上发展了弹簧式光顺法和局部网格重构法两种动态网格变形技术。结合运动轨迹计算方程,将动态网格法应用于飞机外挂物投放问题中,成功模拟了导弹自由投放的整个过程,获得了详细的包括弹体运动速度、运动轨迹和受力情况等在内的丰富的流场信息。成功的应用不仅验证了动态网格法的可行性;而且也表明,动态网格法的进一步完善与发展将成为解决外挂物投放问题的有力工具。