油泵壳体及滑动轴承异常磨损故障研究

主泵调节器用来供给、调节发动机在各种工作条件和工作状态下所需的燃油,如果主泵调节器油泵内部出现严重磨损,势必对发动机性能的发挥和工作可靠性产生重大影响。通过对4起主泵调节器油泵壳体及滑动轴承异常磨损故障的对比、机理分析,找到了故障的主要原因,并制定了针对性的预防措施。     

基于Fluent的电液泵流场与温度场有限元分析

介绍三相异步电机-轴向柱塞式电液泵(EHP)的集成结构与工作原理,计算电液泵机械损耗,在Ansoft软件中建立电液泵电机模型,仿真分析电液泵的电磁损耗,并在此基础上建立有限元耦合模型,借助Fluent软件仿真分析液压油在壳体内腔的流动与温度分布状态,以及关键零部件的温度分布。有限元分析结果表明,液压油可以在流道内充分流动,并且额定工作状态下,当进口液压油温度为35℃时,电机定子最高温度不超过58℃,转子最高温度不超过40℃,散热效果好于传统电动机-泵组。针对定子内部温度较高的现象,研究了定子四周打4个直径10 mm的通孔后的温度分布情况,并与打孔前进行了对比,结果表明,打孔后电机定子最高温度降低了0.6℃,局部区域温度降低超过3℃,散热效果改善明显。     

一种自冷却结构燃油泵滑动轴承润滑特性分析

为研究低介质黏度和自冷却结构限制下的航空燃油泵滑动轴承润滑特性分布规律,基于油膜动压润滑流动的Reynolds方程和等效黏度润滑流动模型,以绝热流动为假设简化滑动轴承内部流动的能量积分方程,构建一种联合Reynolds方程和绝热流动能量积分方程的燃油泵滑动轴承热流动润滑流动模型。采用CFD数值模拟和有限差分法相结合的混合仿真方法,分别对不同的间隙比、偏心率、宽径比条件下的滑动轴承的油膜压力、油膜厚度、油膜温度、端泄漏量、摩擦阻力等润滑特性进行了仿真分析。仿真结果表明:采用CFD计算滑动轴承径向载荷精度优于4.0%;保持偏心率不变,油膜承载力随着间隙比的增加而单调下降,油膜厚度随着间隙比的增高而增加;保持间隙比不变,油膜的承载力随着偏心率的增大也逐渐增大,油膜厚度随着偏心率的增高而下降,而油膜温度与油膜厚度成反比,且随着偏心率的升高,油膜温度的峰值越来越明显;当偏心率、间隙比一定时,可通过增加宽径比提高滑动轴承的油膜承载力。因此在滑动轴承的设计中,需综合考虑油膜承载力、端泄漏量、油膜厚度和温升间的相互制约因素,合理地优化间隙比、宽径比和偏心率以提高滑动轴承润滑性能。      

航空煤油泵轴尾机械密封副材料特性

为选择适合在航空煤油介质中工作的机械密封副材料,对材料的摩擦特性进行了研究,利用摩擦磨损试验机得到不同工况条件与表面粗糙度下材料的摩擦因数、温升,在原子力显微镜(AFM)下对3组典型配对材料的微观磨损形貌进行观测,分析磨粒磨损和黏着磨损的行为差异,计算磨损的关键参数。研究发现:聚四氟乙烯（PTFE)在既定条件下为性能最佳的软材料;硬材料表面粗糙度值为0.05时的摩擦性能最佳,不同硬材料间性能差异不大。研究发现PTFE在配磨材料上产生的犁沟效应最轻微,黏附的元素颗粒最少;黏着磨损会造成表面高度分布函数的偏移,利用离散化求解公式得到了黏着体积与平均黏着厚度。      

An adaptive-order particle filter for remaining useful life prediction of aviation piston pumps

An accurate estimation of the remaining useful life (RUL) not only contributes to an effective application of an aviation piston pump, but also meets the necessity of condition based maintenance (CBM). For the current RUL evaluation methods, a model-based method is inappropriate for the degradation process of an aviation piston pump due to difficulties of modeling, while a data-based method rarely presents high-accuracy prediction in a long period of time. In this work, an adaptive-order particle filter (AOPF) prognostic process is proposed aiming at improving long-term prediction accuracy of RUL by combining both kinds of methods. A dynamic model is initialized by a data-driven or empirical method. When a new observation comes, the prior state distribution is approximated by a current model. The order of the current model is updated adaptively by fusing the information of the observation. Monte Carlo simulation is employed for estimating the posterior probability density function of future states of the pump’s degradation. With updating the order number adaptively, the method presents a higher precision in contrast with those of traditional methods. In a case study, the proposed AOPF method is adopted to forecast the degradation status of an aviation piston pump with experimental return oil flow data, and the analytical results show the effectiveness of the proposed AOPF method.     

某型直升机液压泵特性试验测试系统

液压泵特性试验对测试响应时间要求很高,因此建立一种合理的测试系统是非常重要的.本文从泵的特性测试着手,重点阐述了泵特性试验中主要测量参数压力、流量的测试方法并建立了一种以DP440动态信号分析仪为核心的自动测试系统.     

New reference trajectory optimization algorithm for a flight management system inspired in beam search

With the objective of reducing the flight cost and the amount of polluting emissions released in the atmosphere, a new optimization algorithm considering the climb, cruise and descent phases is presented for the reference vertical flight trajectory. The selection of the reference vertical navigation speeds and altitudes was solved as a discrete combinatory problem by means of a graphtree passing through nodes using the beam search optimization technique. To achieve a compromise between the execution time and the algorithm's ability to find the global optimal solution, a heuristic methodology introducing a parameter called ‘‘optimism coefficient was used in order to estimate the trajectory's flight cost at every node. The optimal trajectory cost obtained with the developed algorithm was compared with the cost of the optimal trajectory provided by a commercial flight management system(FMS). The global optimal solution was validated against an exhaustive search algorithm(ESA), other than the proposed algorithm. The developed algorithm takes into account weather effects, step climbs during cruise and air traffic management constraints such as constant altitude segments, constant cruise Mach, and a pre-defined reference lateral navigation route. The aircraft fuel burn was computed using a numerical performance model which was created and validated using flight test experimental data.     

电动泵与挤压式推进系统对比研究

对电动泵和挤压式推进系统进行了对比研究,主要考虑了气瓶、增压气体、贮箱、电池和电机等因素对推进系统的影响,结果表明:相对于传统的挤压式推进系统,电动泵供应系统已经具有明显的优势,而且能够获得更高的综合性能;锂离子电池具有较大的能量密度和功率密度,更适合应用于电动泵供应系统;采用高性能永磁电机能够使得整个推进系统的质量更轻。在实际推进系统设计时,应综合平衡发动机推力、燃烧室压力和工作时间等参数的影响,才能有效地控制电池和电机的质量,保证整个系统具有较高的综合性能。     

冷气掺混对高压涡轮气动性能影响的数值研究

采用数值方法研究了冷气掺混对高压涡轮气动性能和叶栅通道内部二次流动结构的影响,计算结果表明:冷气流量增加,冷却高压涡轮导叶和转子型面总载荷降低,导叶进、出口马赫数均减小,转子出口相对马赫数在径向0~0.55区域增大而在径向0.55~1.0区域减小.导叶进、出口气流角受冷气流量的变化影响较小.冷气流量由压气机进口流量的4.83%增加至14.49%,转子进口相对气流角在径向0.05~0.95区域增大而出口相对气流角在径向0.6~1.0区域减小,导叶绝热壁面冷却效率先升高后降低而转子绝热壁面冷却效率提高了19.33%.轮毂和机匣封严气呈束状进入转子叶栅通道且腔内封严气流动受旋转轮盘抽吸效应影响较大.      

某高低压泵组件运转后扫膛问题的分析

分析了某高低压泵组件装配运转过程中的一般技术问题基础方法,详细分析了高低压泵组件运转后壳体八字孔扫膛的问题,为提高该类产品的运转合格率提供了分析研究方向。