Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.     

航空燃油齿轮泵滑动轴承非线性瞬态性能数值分析

为研究航空燃油齿轮泵滑动轴承在复杂交变载荷扰动下的瞬态润滑行为,建立了燃油齿轮泵滑动轴承的瞬态计算模型。该模型考虑了滑动轴承油膜空化边界的质量守恒和其所处非线性动态承载环境的影响。在此基础上使用批处理技术实现了燃油齿轮泵和滑动轴承的联合仿真计算,在滑动轴承的瞬态润滑计算过程中计入了燃油泵瞬态内流场和其动态载荷的耦合作用。以此进行了恒定载荷和动态载荷工况下的轴心轨迹稳定性分析以及轴承瞬态润滑性能分析研究。研究结果表明：滑动轴承计算模型的计算结果与实验数据较为吻合,误差保持1.2%以内;燃油齿轮泵的动态载荷对轴心轨迹的影响体现在轨迹启动段偏移的增大以及静平衡位置的消失;通过不同关键参数的对比研究发现：合理的增大宽径比或减小间隙比可以获得更为理想的轴心轨迹静平衡位置,但对于轴承转子运动的稳定性,间隙比由0.2%增至0.6%时,未稳定阶段轴心位置的变化趋势由双峰变为单峰,速度稳定段曲线的波动幅值先增大后趋于不变;当宽径比由0.6增至1.2时,全周期内速度响应曲线的偏移降低,轴心运行的稳定性提高;在轴承瞬态润滑特性中对于轴承载荷变化泄露流量具有的敏感性较强而最小油膜厚度的敏感性较差。     

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

圆转矩形喷管射流掺混特性试验研究

本文采用热线风速仪对圆转矩形收敛喷管的射流流场与掺混特性进行了试验研究,测量了喷口下游不同截面上,射流宽、窄对称面上射流的速度、雷诺剪应力、湍流强度,得到其沿径向和轴向的分布规律。发现在径向方向上,雷诺剪应力先增大后减小,最大值出现在射流与外流的交界面附近,湍流强度则逐渐减小;在轴向上,雷诺剪应力在近喷口区存在小幅波动,而后逐渐减小,湍流度则先略有增大而后变化逐渐减慢。射流特性在宽对称面与窄对称面上的分布规律相同。     

多重网格加速的LUSGS算法用于喷管流场数值模拟

采用有限体积法,二阶精度插值的Roe格式对三维流场N-S方程进行空间离散;采用LUSGS隐式时间推进法和多重网格技术加快计算收敛速度;采用独特的显式算法克服了两方程湍流模型刚性对流场计算收敛速度的影响,并给出了该方法的理论依据。通过轴对称喷管内流场、二元喷管内外流场的数值模拟验证了采用以上方法在计算效率上的提高。最后将RNG模型计算结果与SA模型计算结果及实验数据做对比分析。     

喷嘴挡板式电液伺服阀制造技术创新研究

喷嘴挡板式电液伺服阀是液压系统实现控制功能的常用元件,本文通过在某型号伺服阀产品工艺流程、关键零组件/工序工艺方法、工艺文件等方面进行超出传统方式的改进和试验,完成了其制造技术的创新性实践研究,优化了该类电液伺服阀生产模式,提升了生产效率和能力.     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

高效空间应用燃料电池热能利用技术研究

首先介绍了空间应用燃料电池高效散热及温控技术。高精度控温主要是利用被动散热技术,将产生的热量快速传导至外部冷却介质,从而保证产热面的温度均匀性,实现电池稳定工作。通过嵌入式被动散热和双端散热的冷却方式,实现电堆内部最大温差小于5℃,换热系数达1000W/(m·K)。