Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

断裂韧性可靠性分析的相似计算法

根据断裂力学原理，动用相似理论求出断裂韧性ＫＩＣ〉ＧＩＣ，ＪＩＣ和δＣ之间的相似指标，然后利用正态函数的加法定理，对断裂韧性分散性进行相似计算，从而可以根据已知的断裂韧性随机信息，对难以求解或未知的其它断裂韧性参数进行可靠性分析和推断。计算介绍了一些实际应用。     

BCu93P丝状钎料的断裂分析

针对BCu39P钎料丝材在热挤压过程中易产生断裂，质量不稳定等缺陷，用金相法和扫描电镜（SEM），分析和研究了该钎料丝材的内部组织分布和断口形貌，找出了引起钎料断裂的原因，并提出了解决措施和钎料内部组织分布的理想模型。     

Improving Mode II delamination resistance of curved CFRP laminates by a Pre-Hole Z-pinning (PHZ) process

This paper presents an experimental investigation of the Mode II delamination resistance of curved CFRP laminates reinforced with Z-pins. A Pre-Hole Z-pinning (PHZ) process is developed to reduce the in-plane damage of the Z-pinned laminates. The microstructural observation of the Z-pinned laminate specimens indicates that the PHZ process can effectively decrease the defects including the Z-pin offset angle and the area of eyelet zone. The influences of the volume fraction and diameter of Z-pin on the fracture toughness and the delamination crack growth rate of the specimens under End Notch Flexure (ENF) loading are then determined experimentally. The test results show that Z-pin increases the interlayer stiffness of the laminate. The delamination crack growth rate is reduced with the increase of Z-pin diameter and volume fraction, and a reduction up to 40% is achieved compared with the specimens without pins. Furthermore, the Mode II fracture toughness is significantly improved with the increase of Z-pin volume fraction. When Z-pin volume fraction increases by 1%, the achieved fracture toughness is about 200% higher compared to the unpinned laminates.     

丁羟推进剂定载破坏试验探索研究

研究了丁羟推进剂在定载荷下断裂所需时间与推进剂本身抗拉强度的关系，并且给出了环境温度和湿度，试件大小，形状和制作方法对推进剂断裂所需时间的影响，为固体火箭发动机药柱设计提供了参考数据。     

水分对碳－环氧复合材料Ⅱ型分层韧性的影响

通过研究不同湿热条件下Ｔ３００／９１４Ｃ和Ｔ３００／Ｍ１０两种复合材料的玻璃化转变温度、层间剪切强度和分层断口形貌，分析了水分影响复合材料Ⅱ型分层韧性的机理。结果表明，水分对强界面和弱界面基体体系的作用机理不同，对两类复合材料的分层韧性也有不同的影响。对强界面纤维－基体体系，水分的增塑作用使得其分层韧性增强，而对弱界面体系这种韧性降低。而水分的溶胀作用对两类复合材料的分层韧性都不利。     

固体发动机壳体用D406A钢锻件的断裂韧度KIC测试研究

对固体发动机壳体用D406A超高强度锅锻件,进行了平面应变断裂韧度K_(IC)测试研究,获得了壳体重要部位实用锻件的K_(IC)值;找到了材料强度和断裂韧度合理匹配的碳含量范围,为壳体设计与安全使用及断裂分析提供了试验依据。     

铝合金薄板K_c测试新方法的探讨

通过用圆(或椭圆)孔试件测量金属薄板平面应力断裂韧性Kc的方法,与通过用中心穿透裂纹试件Kc的标准方法相比较之后,将Whitney和Nuismer用于复合层压板中的点应力破坏准则,推广到铝合金薄板Kc的测量。 在理论和实验分析的基础上,拟合出与实验结果相一致的经验公式。     

用奇异有限元法计算正交各向异性复合材料平面断裂的应力强度因子

将复合材料平板视为正交各向异性平板，把正交各向异性平板裂纹顶点附近的位移展开式迭加在一般的等参数单元上，建立了用于复合材料平板应力强度因子计算的奇异元。并以所做出的公式，对正交各向异性板含单边裂纹和双边裂纹问题进行了计算分析，取得了较好的效果。     

TiAlN 涂层钻头钻削钛合金的实验研究

采用Ti Al N涂层硬质合金麻花钻对钛合金(TC4)进行钻削试验,研究了切削用量对轴向力、加工孔壁表面粗糙度和切屑形态的影响。结果表明:轴向力随着进给量的增加而增加,轴向力随着转速的增加而减小。运用指数公式模型对轴向力实验结果进行回归分析,得到轴向力与转速以及进给量之间的关系式,并对该方程进行了检验验证误差均小于7%;随着进给量的增加断屑能力逐渐增加,切屑长度逐渐变短。在低转速和进给量为50 mm/min时切屑形态为短螺旋形切屑,此时排屑和孔壁粗糙度均为最佳。