航天器蜂窝夹层结构复合材料热变形分析

蜂窝夹层结构复合材料在航空、航天结构中已得到了广泛的应用。文章从热变形分析角度出发，对蜂窝夹层结构复合材料的热变形分析问题提出了几点看法。     

碳/环氧面板-铝蜂窝夹层结构件损伤修补工艺

文章介绍了北京空间机电研究所研制的某型号卫星碳 /环氧面板 -铝蜂窝夹层结构件结构特点及损伤情况 ,且对损伤修补内容作了较详细叙述     

不同增强体C/C复合材料韧性研究

研究了编织C/C复合材料、针刺C/C复合材料和毡基C/C复合材料室温、高温的断裂韧性,以及3种不同增强体C/C复合材料的冲击韧性。研究发现,C/C复合材料的高温断裂韧性高于室温,其中针刺C/C复合材料的断裂韧性值最高。编织C/C复合材料的抗冲击性能表现出强烈的各向异性,针刺C/C复合材料抗冲击性能优于毡基C/C复合材料。     

纺织结构复合材料强度性能的研究

考究了由两种不同纺织结构制备的碳繁华只物／环氧树脂复合的制备方法及强度性能，探讨了复合材料强度与织物结构参数－纤维取向之间的关系，导出了计算纺织结构复合强度公式，其估算值与实测值吻合。     

垂直度误差对复合材料单钉连接性能的影响

为揭示连接孔垂直度误差对航空复合材料连接性能的影响规律,对准各向同性碳纤维环氧树脂复合材料板进行了单钉单剪试验研究。以极限承载强度、弦刚度、2%偏移承载强度为指标研究连接孔的倾斜角度、倾斜方向以及螺栓扭矩对接头承载性能的影响规律。试验结果表明:当连接孔倾斜角度从0°增加到4°时,接头弦刚度增大10%~40%,极限承载强度下降9%~12%;连接孔倾斜方向对极限承载强度影响甚微,却可使接头弦刚度产生20%~30%的变化;增加螺栓扭矩可以有效提高极限承载强度,但对接头刚度无明显影响;连接孔倾斜角度越大,则螺栓扭矩的增大对2%偏移承载强度的强化效果越不明显。     

钛合金蜂窝三层结构的扩散焊接研究

介绍了俄罗斯钛合金蜂窝三层结构扩散焊接的研究成果.详细介绍了铝合金、焊接规范选择、接头应力变形状态的分析、模拟计算等,有助于国内钛合金的焊接研究.     

增强碳/碳球锥切削中的最小热应力优化研究

对将增强碳/碳纤维块体切削成球锥外形的工艺,块体热膨胀系数异性轴指向可以极大地影响球锥热应力大小,存在优化设计的潜力。本文对增强碳/碳不同主轴方向弹性模量比值下的球锥最小热应力优化特性进行了研究,发现以1为界,不同模量对比关系下的优化特征是完全不同的。在本文加热条件下,当异性轴模量小于同性面模量时,优化曲线对温度场变化很敏感,以块体异性轴和球锥横截面成±42.9夹角时热应力最小;当异性轴模量大于同性面模量时,优化曲线随加热时间变化不大,以块体同性面与球锥对称轴平行或成小锐角时热应力最小。一般而言,工艺设计中应避免用模量大的主轴方向指向球锥对称轴方向。     

Love Waves in Layered Graded Composite Structures with Imperfectly Bonded Interface

Theoretical analysis and numerical calculations of Love wave propagation in layered graded composites with imperfectly bonded interface are described in this paper. On the basis of WKB method, the approximate analytic solutions for Love waves are obtained. By the interface shear spring model, the dispersion relations for Love waves in layered graded composite structures with rigid, slip, and imperfectly bonded interfaces are given, and the effects of the interface conditions on the phase velocities of Love waves in SiC/Al lay- ered graded composites are discussed. Numerical analysis shows that the phase velocity decreases when the defined flexibility parameter is greater. For the general imperfectly bonded interface, the phase velocity changes in the range of the velocities for the rigid and slip interface conditions.     

不同喷铝参数对复合材料雷击防护性能模拟

为了研究复合材料不同的雷击防护(lightning strike protection,LSP)系统在雷电流作用下的损伤规律,对雷击损伤过程和烧蚀机理进行分析,建立复合材料层合板雷击防护的能量平衡数学模型。在此基础上,在ABAQUS中建立复合材料基准件、全喷铝和局部喷铝防护系统的碳纤维增强复合材料(carbon fiber reinforced polymer,CFRP)层合板电-热耦合有限元模型,和实验结果对比验证模型的有效性,对雷击烧蚀损伤特征进行分析,并引入雷击烧蚀损伤指数DI,得出三种不同模型在不同铝涂层厚度、不同峰值雷电流作用下的烧蚀损伤规律,并对两种不同的局部喷铝防护系统下复合材料的损伤特征进行对比分析。结果表明:雷击防护系统下复合材料的烧蚀损伤面积和铝涂层厚度关系进行函数拟合,两者均满足幂函数关系。     

Microstructure,thermophysical property and ablation behavior of high thermal conductivity carbon/carbon composites after heat-treatment

Uni-directional carbon/carbon composites with high thermal conductivity are suitable to supply continuous thermal protection for future reentry vehicles since they could reduce surface temperature and ablation rates simultaneously in harsh environments. In this work, the high thermal conductivity carbon/carbon composites were prepared by chemical vapor infiltration. After heat-treatment, both their open porosity and internal friction increase due to the fiber/matrix thermal expansion mismatch; while their thermal conductive performance become better due to more complete carbon structure. With raising heat-treatment temperature from 1800 °C to 2450 °C, the mass and linear ablation rates of C/C composites with fibers vertical to the oxyacetylene torch for 60 s decrease from 0.66 mg/s and 2.95 μm/s to 0.51 mg/s and 2.05 μm/s respectively. The improved ablation resistance is resulted from the increased thermal conductivity from 282 to 508 W/(m·K) and more carbon fibers exposed to the flame during ablation, which have better oxidation resistance than those of carbon matrix. While such ablation rates become larger for composites with fibers parallel to the flame, from 1.02 mg/s and 3.73 μm/s to 1.28 mg/s and 5.01 μm/s respectively since the ablation occurred more easily through gaps at the fiber/matrix interfaces, which become larger and are always exposed to the flame for this case.