JL8飞机环控系统的改进

通过对ＪＬ８飞机环控系统的分析得知,在二散出口与涡轮入口之间加装电动活门,需要时关闭活门,限制冷路流量,可以提高座舱供气温度。     

直流电阻测试仪电阻示值误差测量结果的不确定度评定

介绍了一种利用直流标准电阻检定电阻测试仪电阻示值误差测量结果的不确定度评定方法。     

减压器启动冲击解决方案

为消除运载火箭上面级高压贮气增压系统启动过程中对减压器的冲击,提出在减压器前增设限流阀的简易方案。基于减压器启动冲击形成机理,给出了限流阀的设计和结构。结果表明：增加限流阀后,减压器入口压力建立时间推迟,出口压力降低,启动冲击被有效抑制,且稳态工作时限流阀的前后压力基本相同,减压器正常工作不受影响。     

微阵列射流冲击肋化表面传热特性

以去离子水为工质,对微阵列射流冲击光滑和肋化表面的传热特性进行了实验研究,并以光滑表面传热性能为基准,讨论了肋化表面强化因子(ε)变化规律.实验结果表明:①浸没和自由射流的传热系数均受无量纲射流距离(H/d)影响;提高射流Re数和减小无量纲孔间距(S/d)都能够增强换热.②浸没射流ε受H/d影响大,而自由射流ε基本不受H/d影响;两种射流方式的ε都随Re数增大,且渐趋于一个常数.③对流热阻在各种射流情况下均随流量不断下降,但下降趋势逐渐平缓,当流量大到一定时,热阻基本不再降低.      

Effects of Contact Resistance on Heat Transfer Behaviors of Fibrous Insulation

In this article, a numerical model combining conduction and radiation is developed based on two flux approximation to predict the heat transfer behavior of fibrous insulation used in thermal protection systems. Monte Carlo method is utilized to determine the modified radiative properties with experimentally measured transient external temperature as high as 1 000 K. It is found that the estimated radiative properties become time-independent after about t = 3 000 s. By comparing the predicted to the measured results in transient state, the contact resistance exerts significant influences upon the temperature distribution in the specimen. Results show that the averaged absolute deviation is 3.25% when contact resistance is neglected in heat transfer model, while 1.82% with no contact resistance.     

Flow characteristics in a rotor-stator cavity with cooling air inlet at low radius

Experiments were conducted on a typical rotor-stator system where air entered through an annular slot at low radius and flowed out of the cavity axially through a rim seal between the rotor and the stator. For the seal in this rotor-stator system, the stationary shroud overlapped the rotating one. Pressure distributions at the stator surface and flow resistance coefficients of the rotor-stator cavity with a maximum gap of 67mm were measured under different dimensionless mass flow rates from 1.32×104 to 4.87×104 with a large range of rotational Reynolds numbers from 0.418×106 to 2.484×106. The results show that pressure on the stator surface decreases with the increase of rotational Reynolds number when the dimensionless mass flow rate is below 1.3×104; when the dimensionless mass flow rate is above 3.034×104, the trend reverses. This is the so-called "pressure inversion effect". However, dimensionless pressure does not show the same changes when rotational dynamic pressure is chosen as the denominator. The resistance coefficient of the rotor-stator cavity is determined by the dimensionless mass flow rate and rotational Reynolds number; for practical application, the resistance coefficient can also be estimated by the turbulent flow parameter in the range of turbulent parameter from 0.1 to 1.6.      

Microstructure evolution and mechanical anisotropy of M50 steel ball bearing rings during multi-stage hot forging

This study aimed to explore the evolution of flow lines and microstructures of M50-steel bearing ring and the anisotropy of its tensile mechanical properties after Multi-Stage Hot Forging (MSHF) and subsequent spheroidizing annealing (MSHFA). To this end, the present study mainly employed stereo microscopy, Optical Metallurgical Microscopy (OMM), Scanning Electron Microscopy (SEM), and Electron Backscatter Diffraction (EBSD) to characterize and analyze the workpiece at each processing stage of MSHF while performing microhardness measurement and uniaxial tensile experiment to test and analyze the mechanical properties of the workpiece. Macro-structure observation showed that the simulation results of flow lines at each stage were consistent with the experimental results. Microscopic observation showed that, after MSHF, deformation gradually became less significant along the outward radial direction of the bearing ring. After MSHFA, the microstructures of the bearing ring became uniform, whereas primary carbides did not dissolve. The mechanical properties were better in the axial direction (AD) than in the radial (RD) and circumferential directions (CD) after MSHF due to the smaller grain width. After MSHFA, the mechanical properties in the ADs and CDs were better than those in the RDs, which was due to the large cross-sectional area of carbides along the flow-line direction.     

Evolution of wall flow structure and measurement of shear stress issuing from supersonic jet with extended shelf

This paper reports an experimental study on the supersonic jet surface flow structure visualization and shear stress field measurement issuing from a rectangular nozzle with extended shelf. The evolution of the near-field surface flow structures with an increased Nozzle Pressure Ratio (NPR) is successfully captured by the surface oil flow, infrared detection technology, and the Shear-Sensitive Liquid Crystal Coating (SSLCC) technique. Results reveal that under smaller NPR, the wall flow structure is similar to that of a jet without the extended shelf i.e., clean jets, and this is caused by insufficient effect on the boundary layer. However, at higher amplitudes of NPR, there exists a significant effect of the boundary layer, as a near triangular separation forms on the trailing edge of the Mach stem due to the adverse pressure gradient, which is visualized for the very first time in this paper. Furthermore, the vector field of shear stress is measured quantitatively by SSLCC technique. Results shows that the magnitude of shear stress heightened with NPR increasing, and the directions of shear stress changes across the shock wave and expansion fans. In addition, surface streamlines measured by SSLCC is significantly consistent with the streamlines visualized using the oil flow technique.     

低速离心压气机叶尖小翼设计与扩稳机理研究

为了揭示叶尖小翼对离心压气机气动性能的影响机理,采用数值模拟方法研究了NASA低速离心压气机(LSCC)附加不同叶尖小翼的气动特性,并在分析离心叶轮失稳机制的基础上探究了叶尖小翼的扩稳机理.研究结果表明:平顶型小翼对离心压气机性能影响较小,凹槽型小翼均使得压气机效率有所降低.凹槽型压力面小翼方案使得压气机综合稳定裕度增...     

A boundary surrogate model for micro/nano grooved surface structure applied in turbulence flow control over airfoil

The application of grooved surface structure is an emerging and effective means in turbulence flow control. However, for a realistic configuration, the global flow field described directly by simple application of massive grids makes it unfeasible to simulate. In this paper, a boundary surrogate model reproducing the effect of microscopic near-wall region is proposed to improve computational efficiency. The surrogate model trained with Lattice Boltzmann Method(LBM) considering the rarefied effec...