飞机铆接电阻专用测量仪的研制

飞机铆接电阻专用测量仪是用于测量飞机铆接部件接触质量的专用仪器,它对保证飞机机载电子设备和通讯系统正常工作具有重要作用,在飞机维护中也常常要检测机体电阻是否符合要求.本文介绍了该测量仪的研制目的、工作原理和电路组成.     

Silver Film Growth on Glass Ceramic by Radio Frequency Magnetron Sputtering

Thin silver films are deposited by radio frequency magnetron sputtering on glass ceramic at room temperature.Variations of sputtering power,bios voltage and power density are carried out for each deposition,then parts of as-deposited samples are subjected to annealing at 600 ℃ within a vacuum chamber.Structural properties are studied by X-ray diffraction(XRD),scanning electron microscope(SEM)and laser scanning confocal microscope(LSCM).It is shown that structural properties have a strong dependency on sputtering power and annealing temperature.Electrical contact resistance measured by a four point probe instrument is directly affected by the thickness of films.It is also found that the film conductivity,especially in thinner films,is improved by the increasing grain size.Finally,the film adhesion is observed by scratch tests.And the adhesive ability deposited by radio frequency magnetron sputtering shows a better performance than that produced by traditional methods.     

Leading-edge flow separation control over an airfoil using a symmetrical dielectric barrier discharge plasma actuator

In order to promote an in-depth understanding of the mechanism of leading-edge flow separation control over an airfoil using a symmetrical Dielectric Barrier Discharge(DBD) plasma actuator excited by a steady-mode excitation, an experimental investigation of an SC(2)-0714 supercritical airfoil with a symmetrical DBD plasma actuator was performed in a closed chamber and a low-speed wind tunnel. The plasma actuator was mounted at the leading edge of the airfoil.Time-resolved Particle Image Velocimetry(PIV) results of the near-wall region in quiescent air suggested that the symmetrical DBD plasma actuator could induce some coherent structures in the separated shear layer, and these structures were linked to a dominant frequency of f0= 39 Hz when the peak-to-peak voltage of the plasma actuator was 9.8 kV. In addition, an analysis of flow structures without and with plasma actuation around the upper side of the airfoil at an angle of attack of18° for a wind speed of 3 m/s(Reynolds number Re = 20000) indicated that the dynamic process of leading-edge flow separation control over an airfoil could be divided into three stages. Initially, this plasma actuator could reinforce the shedding vortices in the separated shear layer. Then, these vortical structures could deflect the separated flow towards the wall by promoting the mixing between the outside flow with a high kinetic energy and the flow near the surface. After that, the plasma actuator induced a series of rolling vortices in the vicinity of the suction side of the airfoil, and these vortical structures could transfer momentum from the leading edge of the airfoil to the separated region, resulting in a reattachment of the separated flow around the airfoil.     

变循环压缩系统涵道流动计算模型及模式转换倒流判据研究

为了研究双外涵变循环压缩系统的涵道流动匹配规律，发展了涵道流动的计算模型，对压缩系统模式转换过程中外涵道倒流问题的发生机理和影响因素进行了深入分析，总结了压缩系统的倒流判断准则，并基于简化计算模型和全三维计算结果对倒流判据进行了验证。研究结果表明，对于一定的压缩系统匹配状态，存在一个决定涵道匹配状态的临界核心机驱动风扇级(Core Driven Fan Stage, CDFS)总压比，当CDFS的实际工作压比高于临界压比时，压缩系统第二外涵道将发生倒流，反之则系统不倒流。复杂涵道系统内的流动损失和堵塞等特性对临界CDFS总压比有显著影响，为了准确判断压缩系统的匹配状态，需要对其进行精确模化。基于简化模型得到的压缩系统倒流临界线可以推广至全三维状态，本文提出的倒流判别准则具有较高的可靠性和可行性。     

几种流量测量仪表的选择与节能

对国内能源系统常用的几种工业流量测量仪表实际应用选择及节能问题，简要地进行了原理分析和实际应用分析，供使用者优选流量仪表参考。     

摆锤式冲击试验机能量损失检测方法的比较与分析

摆锤式冲击试验机的能量损失包括：指针的摩擦（或接触式电子角位移传感器的摩擦）、空气阻力和摆轴轴承的摩擦所引起的能量损失；基础的冲击、机架和摆锤的振动所引起的能量损失。国内外还没有成熟的测量方法和测量仪器测定基础的冲击、机架和摆锤的振动所引起的能量损失，没有形成技术文件，目前摆锤式冲击试验机能量损失的检测主要针对前者。本文针对国内计量部门计量摆锤式冲击试验机所依据的常用标准和规程，比较能量损失的检测方法和计算公式，做出简要分析，指出某些计算公式值得商榷之处。     

基于动态故障树的故障隔离程序分析方法

传统的故障隔离程序采用常规静态故障树进行故障分析，可能会导致故障原因分析不全、故障隔离路径过于繁琐等问题。提出基于系统原理和动态故障树进行故障隔离程序分析的方法，以某飞机防火系统引气导管过热探测系统故障为实例，进行系统设计原理和故障告警逻辑分析，引入动态逻辑门，构建具有顺序相关、功能相关和备份关系的动态故障树；在此基础上进行关联故障分析和排故流程图转化。结果表明：该方法能系统地、全面地反映故障触发逻辑，提供快速、准确、有效的故障隔离程序，提高飞机维修保障水平，在复杂飞机系统的航线维修领域具有良好的应用前景和推广价值。     

Numerical investigation of aerodynamic flow actuation produced by surface plasma actuator on 2D oscillating airfoil

Numerical simulation of unsteady flow control over an oscillating NACA0012 airfoil is investigated. Flow actuation of a turbulent flow over the airfoil is provided by low current DC surface glow discharge plasma actuator which is analytically modeled as an ion pressure force produced in the cathode sheath region. The modeled plasma actuator has an induced pressure force of about 2 k Pa under a typical experiment condition and is placed on the airfoil surface at 0% chord length and/or at 10% chord length. The plasma actuator at deep-stall angles(from 5° to 25°) is able to slightly delay a dynamic stall and to weaken a pressure fluctuation in down-stroke motion. As a result, the wake region is reduced. The actuation effect varies with different plasma pulse frequencies, actuator locations and reduced frequencies. A lift coefficient can increase up to 70% by a selective operation of the plasma actuator with various plasma frequencies and locations as the angle of attack changes. Active flow control which is a key advantageous feature of the plasma actuator reveals that a dynamic stall phenomenon can be controlled by the surface plasma actuator with less power consumption if a careful control scheme of the plasma actuator is employed with the optimized plasma pulse frequency and actuator location corresponding to a dynamic change in reduced frequency.     

航天器空间环境干扰力矩分析与仿真研究

针对航天器在轨运行时所受到的空间环境干扰力矩进行建模分析,并通过实时解算和矢量叠加的方式进行仿真研究,尤其对太阳光压力矩与大气阻力力矩的建模与仿真提出了新的方法,该方法通过建立光照面与迎风面的判断准则,准确地对太阳光压力矩与大气阻力力矩进行了估计。对各种空间环境干扰力矩的精确建模与仿真为航天器精确姿态控制设计及系统姿态控制方案和控制执行机构的选取提供了依据,文中提出的方法简单易用,工程实现性强,为未来的工程应用提供了一定的理论依据。     

Mechanism of stall and surge in a centrifugal compressor with a variable vaned diffuser

To expand the stable operating range of compressors, understanding the mechanism of flow instability at low flow rates is necessary. In this paper, the mechanism of stall and surge in a centrifugal compressor with a variable vaned diffuser is experimentally investigated, where the diffuser blade setting angle can be adjusted. Many dynamic pressure transducers are mounted on the casing surface of the compressor. From the design condition to surge, dynamic pressure data is recorded throughout the gradual process. According to the signal developing status, the typical modes of compressor instability are defined in detail, such as stall, mild surge, and deep surge. A relatively high-frequency stall wave originates in the impeller and propagates to the diffuser, and finally stimulates a deep surge in the compressor. The compressor behavior during surge differs at different diffuser vane angles. When the diffuser vane angle is adjusted, both the unstable form and the core factor affecting the overall machine stability change. A specific indicator is proposed to measure the instability of each component in a compressor, which can be used to determine the best region for stability extension technologies, such as a holed casing treatment, in different compressor applications.