弹射动力系统燃气发生器流热固耦合数值研究

为了判断弹射动力系统燃气发生器工作的安全性,需要预示工作过程中燃气发生器壳体的力学响应。基于软件CFX和ANSYS,建立了燃气发生器复合结构流热固耦合仿真模型。对燃气发生器内流场和结构温度场进行流热耦合计算,并将壳体温度场计算结果与试验数据进行对比,再将算得的燃气压强分布与结构温度场分布导入ANSYS以计算结构的力学响应。计算结果表明,燃气发生器工作过程中,直筒段最高温度点位于直筒段与后封头连接的绝热层缝隙处,后封头最高温度点位于后封头与喉衬配合部位的上游端。结构最高温度值仅354K,说明热防护良好;直筒段和后封头壳体主体区域应力安全系数>3,满足设计要求,而在法兰附近圆角过渡处外壁存在应力集中,最大应力处安全系数降为1.13,燃气发生器壳体仍处于安全状态,但存在安全裕度显著降低的风险。     

Flow field design and process stability in electrochemical machining of diamond holes

The metal grille, commonly composed of an amount of diamond holes, has been grow-ingly used as a key structure on stealth aircraft. Electrochemical machining (ECM) promises to be increasingly applied in aircraft manufacturing on the condition that process stability is guaranteed. In this work, a flow field model was designed to improve the process stability. This model is endowed with a variety of flow channel features, together with vibrating feeding modes. The flow field distribution on the bottom surface of the diamond hole was discussed and evaluated as well. The numerical results show that a short arc flow channel could significantly enhance the uniformity of electrolyte velocity distribution and a vibrating feeding of the cathode enables to reduce both fluctuations of the electrolyte velocity and pressure on the bottom surface of the diamond hole. Consequently, the flow field mutations were eliminated. It is verified from the experimental results that a short arc flow channel, when combined with vibrating feeding, is capable of improving machining localization and process stability markedly. What is more, the side gap on the bottom surface of the diamond hole could also be reduced by the abovementioned approach.     

小型二冲程汽油机缸体气口尺寸的确定及其对整机性能的影响

本文以一种典型小型二冲程汽油机为例，介绍了缸体气口尺寸的确定方法，并通过发动机台架试验的结果分析气口尺寸、形状、气道质量对整机性能的重要影响。为进一步提高产品质量，提供了可靠的依据。     

钢筋混凝土小偏心受压构件对称配筋截面设计

通过对钢筋混凝土结构设计规范(GB50010-2002)中有关小偏心受压构件对称配筋简化计算的分析, 经统计分析推出通过解二次方程求解ξ的近似方法,该方法计算简捷、精度较高,可供工程设计人员参考。     

结构随机跳变系统的条件滤波新方法

提出了不完全状态及控制信息的结构随机跳变系统的滤波方法，解决了结构随机跳变系统在控制入与状态的观测互为相关情况下，系统的状态以及不确知的控制输入的最优估计问题。并以线性高斯情况为例进行了数字仿真，证明了该方法的有效性。     

用二次子结构法对过盈螺纹进行应力分析

针对过盈螺纹的疲劳寿命估算进行了工作,求解应力是寿命估算的第一步。为减少求解自由度,节省机时,提高效率,文章根据螺纹配合的特点,提出二次子结构法,消去内部节点,只留下配合点、加载点和边界约束点。 文章推导了子结构公式及过盈配合公式,给出了程序流程图及有限元计算结果,由结果可知,随过盈量增加,齿间应力差减小;而随过盈量增加,危险点相当应力增大。这些结果,对过盈量的选择也有参考价值。     

热线风速仪在紊流流场测量中的应用

本文综合分析了目前采用热线风速仪测量紊流流场的各种方法,并着重指出,在高紊流度情况下,还没有比较可靠的方法。在使用目前推荐的各种计算公式时,必须首先验证其公式的可靠性,并注意其限制性条件。     

等热流条件下相变导热仿生优化

为强化微重力条件下相变材料的熔化释冷过程,采用仿生优化的思想和有限元方法研究了导热空间内高导热材料的最佳布置方案。研究表明,采用温度梯度的时间积分作为布置高导热材料的判断标准,可把导热仿生优化的思想的应用由稳态问题扩展到非稳态具有相变的问题。和人工构造方案法相比,仿生优化得到的方案可以明显强化释冷过程、降低热流入口温升;且能克服其工作量大,所得方案不一定包含最优方案的不完备性问题。     

Simulation and experimental investigation on a dynamic lateral flow mode in trepanning electrochemical machining

An appropriate flow mode of electrolyte has a positive effect on process efficiency, surface roughness, and machining accuracy in the electrochemical machining(ECM) process. In this study, a new dynamic lateral flow mode, in which the electrolyte flows from the leading edge to the trailing edge, was proposed in trepanning ECM of a diffuser. Then a numerical model of the channel was set up and simulated by using computational fluid dynamics software. The result showed that the distribution of the flow field was comparatively uniform in the inter-electrode gap. Furthermore, a fixture was designed to realize this new flow mode and then corresponding experiments were carried out. The experimental results illustrated that the feeding rate of the cathode reached 2 mm/min, the best taper angle was about 0.4°, and the best surface roughness was up to Ra= 0.115 lm. It reflects that this flow mode is suitable and effective, and can also be applied to machining other complex structures in trepanning ECM.