现代远程教育的媒体素材构建方法

本文阐述了媒体素材的采集及处理方法 ,对现代远程教育工程建设可提供有效的帮助     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

浅析运输类飞机经济舱头排旅客座椅头部损伤判据的影响因素

介绍了头部损伤判据HIC的概念、适航要求及影响运输类飞机客舱头排旅客座椅HIC的相关参数;叙述了旅客座椅头排距、头部撞击壁板的刚度、安全带织带伸长率、乘坐摩擦系数等参数的影响和重要程度;对如何设计符合HIC要求的经济舱头排旅客座椅和壁板提出了建议。     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

判断力权值的确定方法及AHP中群组判断矩阵的形成

在ＡＨＰ模型中，请一组专家对某一属性进行评价，根据专家的判断能力，给出判断力权值，再通过适当的数学处理方法，可得最优判断矩阵，这是ＡＨＰ中构造判断矩阵的一种新方法。     

跨声速风洞斜孔壁非线性流动试验

为分析跨声速风洞斜孔壁近壁区域的流动特性，评估气流偏角-压力系数的非线性关联，在0.6 m跨超声速风洞中开展了基于七孔探针的流动特性测量试验。通过气流偏角和压力系数分布分析了斜孔壁流动的差阻特性，以及马赫数、模型升力对斜孔壁流动的影响，最后基于试验结果发展了计算斜孔壁特性参数的微分法，并与经验方法结果进行对比。结果表明，斜孔壁流动呈现出明显的差阻性和非线性，在负压差范围内，近壁流动仍以出流为主；高亚声速时，空风洞模型区孔壁流动特性趋于实壁；安装模型后，随着升力的增大，升力面对应的孔壁区域流动向入流发展，孔壁流动特性趋于开口边界。     

GaInP2外延膜中施主—受主对复合发光带的能量关量

通过变温与变激发强度的近红外光致发光研究了用ＭＯＣＶＤ方法、生长在ＧａＡｓ衬底上的Ｇａ０．５Ｉｎ０．５Ｐ（ＧａＩｎＰ２）外延薄膜的１．１７ｅＶ发射带的发光特性。１．１７ｅＶ发光带性质与０．９９ｅＶ及０．８５ｅＶ发光带的性质有着明显的差别。１．１７ｅＶ发光带的机理可用施主－受主对的复合发光来解释，其中施主－受主对系白处在Ｇａ格位上的Ｓｉ（ＳｉＧａ）及其最邻近的Ｇａ空位（ＶＧａ）所组成，记作ＳｉＧａ－ＶＧａ。考虑到ＧａＩｎＰ２中存在着很强的电子－格子耦合作用及其Ⅲ族子格子为部分有序，所以在施主－受主对复合发光中应计及Ｆｒａｎｃｋ－Ｃｏｎｄｏｎ位移△ＦＣ及该对在等效的部分有序势场中的相互作用能Ｅｓ（ＤＡＰ）。Ｘ—射线衍射实验表明，部分有序结构相当于成分调制，因而可用Ｋｒｏｎｉｇ－Ｐｅｎｎｅｙ模型来计算Ｅｓ（ＤＡＰ）值。这样，我们就导出了施主－受主对复合发光的新的能量表示式。     

正电子素络合形成研究(Ⅱ)

本文讨论了不同测量条件对正电子素络合反应速度常数测定值的影响。实验结果表明,在稀溶液的条件下,使用我们特殊设计的盛装溶液的匣式容器能大大提高放射源的使用率并能完全避免放射性废水。     

铝合金T型材拉弯成形的有限元模拟

针对目前拉弯成形中的问题,采用有限元模拟的方法,对带下陷拉弯过程进行计算机仿真,得到优化后的工艺参数,避免了盲目的试拉,提高了加工效率,降低了拉弯成本,积累了带下陷拉弯成形的经验,提高了公司拉弯工艺水平。