声表面渡(SAW)力传感器

本文对声表面波(SAW)力传感器的基本工作原理进行了理论分析,同时对该传感器进行了实验研究。实验获得了约2.3kHz/9.8×10~(-3)N 的力灵敏度。实验表明该传感器是一个线性传感器,对于微力测量十分敏感。     

原子谱线参数的辨识方法

在一种原子谱线参数测量的辨识方法基础上编制了一套原子港线参数辨识的标准软件。用此软件对纯氩和氩、氮混合非平衡电弧等离子体射流的原子谱线进行了处理，获得了射流的电子温度、气体平动温度、电子和原子数密度。状态诊断表明；实验条件下的等离子体射流除中心点为ＬＴＥ外非平衡效应是非常显著的。     

冷热量测试技术研究(英文)

大型中央空调的普遍使用带来了一个新的问题 :各用户消耗能量的准确测量、费用的分摊是否合理等 ,直接影响到现代物业管理的水平 ,因此冷热量测量技术的研究迫在眉睫。本文通过理论分析影响中央空调系统冷热表测量的相关数据 ,建立了数学模型 ,确定了测量方案 ,解决了测量中存在的问题 ,并完成了冷热表的样机制作工作。通过试验数据 ,反复修正仪表的软件和硬件部分。目前该仪表的测量精度较原理样机有较大的提高。经若干用户使用表明 ,该仪表是具有较高性能的实用测量装置     

低压下V形火焰稳定器后回流区流动特性研究

本文用双通道热线风速仪对低压下V形火焰稳定器后回流区流动特性进行了实验研究,获得了局部平均速度、素流强度、雷诺应力等参数的分布情况。实验表明,与常压比较,低压下回流区范围有所缩小,回流流量相对降低,雷诺应力普遍下降,紊流尺度略有增加,从流体力学方面为分析低压下稳定器的燃烧性能提供了新的依据。     

Design and examination of a turboprop inlet with scavenge duct

The inlet with scavenge duct is an important part of turboprop aircraft engine. This type of inlet normally has a complex shape, of which the design is challenging and directly affects the flow field quality of the engine entrance and thus the engine performance. In this paper, the parametric design method of a turboprop aircraft inlet with scavenge duct is established by extracting and controlling the transition law of the critical characteristic parameters. The inlet’s performance and internal flow characteristics are examined by wind-tunnel experiment and numerical simulation. The results indicate that a flow tendency of winding up on both sides is formed due to the induction of the inlet profile, as well as a vortex pair on the back side of the power output shaft. The vortex pair dominates the pressure distortion index on the Aerodynamic Interface Plane (AIP). In addition, with the increase of freestream angle of attack, the total-pressure recovery coefficient of the inlet increases gradually while the total pressure distortion index decreases slightly. On the basis of the experimental results under different working conditions, the parametric design method proposed in this paper is feasible.     

弯曲壁面流动分离及再附的尺度解析模拟

为准确预测弯曲壁面发生的流动分离及再附现象,基于模拟应力混合思想构建了新的RANS/LES混合框架,涡黏系数和湍动能耗散项中的长度尺度同步切换、涡解析区动态确定亚过滤尺度模型系数、采用混合过滤尺度匹配动态模型,并据此构造了k-ω基动态应力混合模型。首先利用槽道湍流检验了基准的亚过滤尺度模型和近壁RANS模型,前者解析获得了正确的湍流脉动近壁行为和相干结构,后者以很小代价捕捉到了雷诺应力分量的各向异性和松弛效应。随后利用周期性山算例考核了动态应力混合模型对分离再附湍流的预测精度,并与DDES,IDDES及SAS模型进行了对比。结果表明,三项改进使得动态应力混合模型具有近壁模拟能力且不存在对数律不匹配问题,涡解析能力优于DES类隐含的准代数模型,能够更好地捕捉压力梯度诱导的流动分离和再附,获得更为准确的壁面剪切应力、摩擦系数、压力系数、回流区,分离剪切层相干结构的分辨率更高。     

涡轮叶片内部微小V肋-凹陷涡复合冷却流动与传热数值模拟

为强化航空发动机涡轮叶片内冷通道传热性能,针对带有微小V肋-凹陷涡高效复合冷却结构矩形通道,采用Abe Kondoh Nagano （AKN） k-ε湍流模型数值模拟研究了肋高与凹陷深度组合对流动传热特性的影响机理。结果表明,当凹陷深度一定,复合结构的强化换热效果随肋高增加而增加,3mm肋高复合结构的传热相比纯凹陷提高了87.1%;当肋高一定,传热随凹陷深度增加先增强后基本保持不变,6mm深凹陷复合结构相比纯V肋提高了52.8%。通过在凹陷上游布置V肋,增强了越过V肋冲入凹陷内流体的湍动能,从而使凹陷前部回流区减小;同时来自微小V肋的涡流与凹陷内部的涡流相互作用,增强了整个流场的动量和热量输运,使通道换热均匀,并相较纯凹陷或纯V肋结构均有显著提升。     

弹射动力系统燃气发生器流热固耦合数值研究

为了判断弹射动力系统燃气发生器工作的安全性,需要预示工作过程中燃气发生器壳体的力学响应。基于软件CFX和ANSYS,建立了燃气发生器复合结构流热固耦合仿真模型。对燃气发生器内流场和结构温度场进行流热耦合计算,并将壳体温度场计算结果与试验数据进行对比,再将算得的燃气压强分布与结构温度场分布导入ANSYS以计算结构的力学响应。计算结果表明,燃气发生器工作过程中,直筒段最高温度点位于直筒段与后封头连接的绝热层缝隙处,后封头最高温度点位于后封头与喉衬配合部位的上游端。结构最高温度值仅354K,说明热防护良好;直筒段和后封头壳体主体区域应力安全系数>3,满足设计要求,而在法兰附近圆角过渡处外壁存在应力集中,最大应力处安全系数降为1.13,燃气发生器壳体仍处于安全状态,但存在安全裕度显著降低的风险。     

高精度测量燃气轮机叶片前缘的三维轮廓

为了解决高精度测量燃气轮机叶片前缘三维轮廓的难题,提出了一种基于球阵列标定检验方法,直接对金属表面的叶片前缘三维轮廓进行高精度测量的相位轮廓测量系统.通过多角度数据融合算法和非线性最小二乘的递归算法,最后高精度测量出叶片前缘三维轮廓,对叶片前缘16个剖面进行拟合,得出了叶片前缘半径和前缘圆心.结果显示:叶片前缘测量系统、方法和算法的综合误差为±0.03mm.此实验装置和方法测量效率高、精度高,将叶片测量和模型化技术推进了一步.      

Flow field design and process stability in electrochemical machining of diamond holes

The metal grille, commonly composed of an amount of diamond holes, has been grow-ingly used as a key structure on stealth aircraft. Electrochemical machining (ECM) promises to be increasingly applied in aircraft manufacturing on the condition that process stability is guaranteed. In this work, a flow field model was designed to improve the process stability. This model is endowed with a variety of flow channel features, together with vibrating feeding modes. The flow field distribution on the bottom surface of the diamond hole was discussed and evaluated as well. The numerical results show that a short arc flow channel could significantly enhance the uniformity of electrolyte velocity distribution and a vibrating feeding of the cathode enables to reduce both fluctuations of the electrolyte velocity and pressure on the bottom surface of the diamond hole. Consequently, the flow field mutations were eliminated. It is verified from the experimental results that a short arc flow channel, when combined with vibrating feeding, is capable of improving machining localization and process stability markedly. What is more, the side gap on the bottom surface of the diamond hole could also be reduced by the abovementioned approach.