膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

自适应流通机匣处理改善压气机性能的机理

为了探索自适应流通机匣处理形式影响跨声压气机性能及流场的流动机理,文中采用非定常数值模拟方法研究了自适应流通机匣处理对NASA轴流Rotor37气动性能的影响。数值计算结果表明:自适应流通机匣处理能有效地延迟失速并在大部分流量范围内略微提高压气机的效率。通过详细的流场分析表明,该机匣处理能有效地增大叶顶区的气流进气角度,抑制了间隙泄漏涡在叶顶通道内的发展,同时阻止泄漏涡涡核在通过激波后破碎,提高了转子顶部通道的流通能力,进而减少叶顶区的流动损失。     

小冲击间距下带倾角冲击凹柱面流场结构实验研究

针对带倾角冲击凹柱面靶板的流动特性和流场结构研究,采用烟线法开展了流场显现实验研究,重点分析了旋流产生和发展的规律。试验中通过改变冲击雷诺数、冲击间距比(冲击间距和冲击孔直径之比)、冲击角度以及凹柱面相对曲率等参数,分析了涡出现的位置、结构等随这些参数的变化规律。研究结果表明:由于冲击射流同周围静止空气之间的粘性作用、气体在凹柱面上运动、脱离的共同作用下,带倾角冲击凹柱面靶板产生了不同的旋流结构。实验中,随冲击雷诺数的增加,在冲击滞止区域两侧流体冲击靶板分离处的圆心角增大,分离推迟;由于冲击角度的影响,相对冲击角度较小侧射流与壁面分离比在较大侧提前,且在相对冲击角度较小侧更容易产生旋流结构。实验中改变的参数均影响了旋流结构及其发展特性,并且影响规律表现出较强的关联性。     

某燃气涡轮工作叶片裂纹分析

为阐明测试单元环境下加速任务试车(AMT)过程中叶片早期起裂的物理原因,对裂纹叶片断口进行了检查和分析,并采用LPTi's XactLIFETM系统对叶片进行了深入的分析.结果表明:叶片叶型发生了过量的蠕变损伤,此过量的蠕变损伤导致了叶片的过量延伸以及叶型特别是在尾缘区域的转扭,此行为可能造成AMT疲劳循环条件下缘板以下的叶片伸根部位疲劳裂纹的形核与生长.因此,过量的蠕变被认为是整个裂纹形核过程的主要驱动力.      

红外搜索跟踪系统单机运动测距方法研究

机载红外搜索跟踪系统只能测量目标的方位、俯仰角度信息,而无法直接获取目标的距离信息。因此需通过载机平台的机动运动,提高系统可观测性,从而对目标距离进行解算,为火控系统提供完整的目标运动参数,实现对目标的被动攻击。通过建立红外搜索跟踪系统（IRST）单机运动测距的数学模型,针对伪测距的非线性滤波的有偏特点进行了去偏处理,获得无偏的单机运动测距模型,并通过数字仿真进行算法模型的仿真验证,验证了算法的有效性。     

基于广义S变换进行雷达信号时频滤波去噪

S变换自问世以来,凭借其优越性已经被广泛地应用于数字信号处理中。针对深空目标雷达回波信号的复杂性,为了得到较好的雷达回波信号,将基于广义S变换的时频滤波应用于雷达回波信号去噪中,并利用低通滤波器设计了时频滤波算子,克服了传统滤波去噪方法滤波因子不能随时间、频率变化而变化的缺陷。通过理论分析与仿真波形对比表明,滤波后能有效地去除噪声,很好地保留了原始雷达回波信号的信号特征,展示了基于广义S变换的时频滤波的可行性,为雷达回波信号去噪提供提供了一种很好的方法。     

跑道侵入概念中的地面保护区研究

为了便于信息交换、数据对比以及不安全事件的研究、分析和防范,亟待明确跑道侵入的外延与内涵。目前国际民航组织关于“跑道侵入”概念中存在一个“地面保护区”的术语,业内人士对其理解不尽相同。在综合考虑升降带、端安全区、仪表着陆系统场地保护区、无障碍区域、障碍物评价面等限制条件的基础上,对地面保护区的划设提出了明确的意见。结论支持并丰富了国际民航组织有关跑道侵入的定义。