三维侧面突扩燃烧室冷态气流场的数值模拟

本文对四侧30°进气并带有进气管道和尾喷口的突扩燃烧室冷态气流场进行了数值模拟.对这种复杂非规则边界的计算区域,首次采用分段算法进行计算.结果表明:分段算法可以提高网络利用率,缩短机时,消除虚假扩散,提高计算准确度,计算结果与试验结果基本符合.     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

某型飞机数字防滑刹车控制盒可靠性分析与设计

对某型飞机数字防滑刹车控制盒的可靠性进行了分析,利用工程加权法对控制盒进行了可靠性分配,并通过元器件可靠性预计法对控制盒的可靠性进行预计.对比及验证表明,控制盒可靠性设计合理,满足主机及系统要求.     

基于线性规划的多操纵面重构控制研究

为实现多操纵面飞机的重构控制,提高飞机飞行的安全性能,提出了一种基于线性规划的多操纵面重构控制策略.针对操纵面卡死、松浮、损伤等典型故障情况,推导了相应的重构分配器,通过基于线性规划的直接分配方法来实现在操纵面故障下的重构控制.仿真结果表明,该控制策略能有效处理典型操纵面故障,发生故障时仍能快速跟踪控制指令,保证较好的...     

一种卫星信道的反馈优化接入机制

提高卫星信道资源利用率，探索高效可行的端站接入机制是卫星通信发展亟待解决的问题之一。当前卫星通信DVB-RCS标准基于带宽预先规划的接入机制与端站随遇接入的需求矛盾凸显，因此提出一套信道反馈优化接入机制，综合考虑各端站数据业务需求，在不改变原有协议信令特征的基础上，探索性地引入谦虚度激励方法，创造性地构造动态协商反馈模型并加以求解，达到提高端站接入数量、满足随遇接入需求、提升信道利用效率、最大化整体带宽通信业务效益的目的。通过试验验证，带宽分配反馈优化机制比传统模式提高近1倍接入率，最大端站数接入时算法耗时约只有0.67s，可为卫星信道使用提供技术参考。     

Experimental study on plasma jet deflection and energy extraction with MHD control

This paper presents an integrated research scheme for vector deflection and energy extraction in a gas plasma jet under Magneto-Hydrodynamic (MHD) control. A MHD-controlled thrust-vector test rig was used to conduct the experimental research. A gas plasma was obtained by injecting ionization seeds of Cs₂CO₃ into the combustion chamber via artificially forced ionization. The effects of the gas temperature and ionization seed mass fraction on the plasma jet deflection and energy extraction were experimentally verified under an applied magnetic field. The experimental results were analyzed theoretically. The results showed that the deflection amplitude of the gas plasma jet and the extracted voltage signal intensity increased with increasing gas temperature and the ionization seed mass fraction. The extracted dynamic voltage signals proved that the ionization seeds of Cs₂CO₃ induced gas ionization at 1173 K. The experiment verified that it is feasible to simultaneously achieve jet deflection and extract energy under the action of an external magnetic field.     

导风轮叶片偏置对高压比串列离心压气机性能的影响

为提升高压比串列离心压气机的性能,借鉴常规一体化离心叶轮中偏置分流叶片的方法,针对某高压比串列离心压气机,应用数值仿真手段分析了串列叶轮中导风轮叶片周向偏置对压气机流场和性能的影响。通过对不同导风轮叶片偏置方案下压气机流场的分析,建立了压气机流动损失与偏置参数的关联性。研究表明:采用较大的偏置参数γ可降低导风轮叶片1前缘的激波强度,改善激波作用导致的泄漏涡破碎和流动分离,但过大或过小的γ方案中导风轮叶顶会出现二次泄漏致使低能流体的掺混损失增加;γ=65%方案压气机综合性能最佳,其压比和效率较γ=50%分别提高了1.5%和1.4%;对于串列离心压气机导风轮叶片周向位置的优化,在避免导风轮叶顶形成较强二次泄漏的前提下,应考虑采用较大的偏置参数γ,同时应防止诱导轮尾迹流体参与导风轮的叶顶泄漏。     

基于功能脆弱性的空中交通相依网络流量分配

依据空中交通管理与航班运行规则,采用复杂网络理论构建由机场、航路与管制扇区组成的相依网络模型,建立不同扰动策略的影响规则,提出以网络流量熵和交通流损失比变化率为指标识别网络功能脆弱性。并以网络总流量熵最小为目标,建立基于改进遗传算法的网络流量协调分配策略,以降低空中交通相依网络的脆弱性。以民航华北地区空域为原型,发现了其相依网络脆弱性表现规律和脆弱源,采用遗传算法求解网络流量分配方案,优化结果降低了网络总熵值和功能脆弱性,其中机场网络流量分配后效果最为显著,验证了方法的有效性,研究结果可为空中流量管理决策提供一定的理论支撑。