飞机纵向静稳定度补偿

讨论了利用飞行控制系统对静不稳定飞机的三种补偿方式：延迟俯仰速度反馈、迎角反印刷品几法向过载负反馈。从而改变了飞机特性，诸如减轻质量，提高升阻比，增强机动性等。最后对三种补偿方案进行了比较，采用迎角反馈补偿是最直接有效的手段，但在工程实践中，往往采用俯仰速率和迎角混合反馈补偿方式。     

从非稳态飞行中确定飞机的纵向平衡曲线

介绍了俄罗斯飞行研究院广泛应用的从非稳态飞行中确定飞机纵向平衡曲线的试飞方法。该方法具有对试飞员动作要求宽、每个动作所包含的信息量大、节省起落、缩短试飞周期的优点。同时,还就该方法所存在的不足进行了讨论。     

从PCI-A429芯片谈内核的设计及集成

以自行研制的PCI-A429芯片为例,讨论了内核设计以及系统集成中内核互连的问题。主要介绍了程控配置和自适应方式的两种ARINC429接收模块内核和PCI内核的设计。还分析了内核之间互连的多种控制接口和数据接口。     

推力向量控制方案及计算

本文归纳推力向量控制的主要方案,着重介绍摆动喷管、流体二次喷射方案的计算思路和结果.摆动喷管中的流场计算要考虑导弹偏摆对所产生的惯性力的影响;所得壁面压力畸变图说明,它是一个三维流场.在摆动喷管设计中要将铰链力减至最小,流体二次喷射的侧向力通过“等效实体模型”,用爆炸波的解来计算.     

高职院校校内实验实训基地管理机制研究

在强调高职院校实训基地重要性的基础上，提出了高职院校实验实训基地的建设思路及管理方式。校内实验实训基地按专业体系进行优化重组，实现资源的优化配置，提高资源利用率，避免重复建设，使实验实训基地向技术开发和技术培训转变，实现教学、生产、培训的有机结合。     

SINS／GPS组合系统的蒙特卡洛仿真

以考虑位置误差相关项的伪距率观测模型，对遥感中使用的SINS/GPS为距、伪距率组合系统进行了蒙特卡洛仿真。结果表明，组合系统的长期位置精度能达到5m以内；GPS数据更新率低于SINS，在GPS测量时间间隔内，组合系统的性能仅由SINS决定，虽然SINS的误差随时间积累，但在GPS测量时间间隔为秒数量级的情况下，即使采用中等精度的惯性的误差随时间积累，但在GPS测量时间间隔为秒数量级的情况下，即使采用中等精度的惯性仪表，其相对位置精度可达到厘米级（这里相对位置精度指组合系统在GPS测量时间间隔内位置误差的变化范围）。     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

基于特征的数控编程技术在航空企业的推广应用

针对国内航空企业飞机结构件数控编程中存在的重复工作量大、效率低、质量不稳定、规范性差等问题,通过面向多主机厂推广基于特征的数控编程技术,切实提高飞机结构件数控编程的效率与质量.首先概述了基于特征的快速程编(FBM NUAA)系统的整体架构,并且介绍了基于特征的数控编程技术在多家主机厂中的推广与应用情况,以及前期推广中遇到的问题,并提出了解决方案.根据多主机厂多机型过百项飞机结构件的实际应用结果表明采用基于特征的快速程编系统进行数控编程,刀轨平均自动生成率超过90％,编程时间较传统编程方式平均缩短70％以上.     

面向高级在轨系统的动态服务质量保证方法研究

AOS(Advanced Orbiting System,高级在轨系统)已经逐渐被各国空间组织采用,随着空间任务的发展趋势更多样化和复杂化,对AOS的QoS(Quality of Service,服务质量)也提出了更高要求.针对AOS服务质量的提升需求,提出了一种虚拟信道优先级策略,使用大容量缓存结合数据压缩动态策略和遥测数据抽帧策略相结合的QoS保证方法,通过分析返向链路带宽与航天器遥测用户带宽的裕量,可以动态调整QoS保证,以适应不同应用环境下的航天器AOS的QoS保证需求.通过模拟不同的工况进行仿真试验,结果表明,该AOS服务质量保证方法适用于返向链路带宽裕量充足和不足的工况,比传统的全同步策略和同步异步结合策略拥有更广泛的适应范围.