低速风洞带螺旋桨动力模型支架干扰实验研究

本文给出了 FL-8风洞中螺旋桨处于不同位置的三个飞机模型支架干扰实验结果,分析了影响带螺旋桨动力的飞机模型支架干扰的因素。实验表明,由于螺旋桨滑流的诱导和夹带作用,使腹撑支杆附近的气流沿轴向加速;由于模型支杆的存在,将影响螺旋桨滑流的空间位置和尺寸,这些都将影响支架干扰量的大小,因此,一般不能用无螺旋桨动力模型的支架干扰数据代替有螺旋桨动力模型的支架干扰数据。实验结果还表明,滑流存在对阻力、俯仰力矩支架干扰有一定影响,其影响量与螺旋桨的位置和拉力系数有关。滑流对升力、滚转力矩和偏航力矩支架干扰无明显影响。除单发右停顺状态外,滑流对侧向力支架干扰无明显影响。     

模块化空间可展开天线支撑桁架结构的热-结构分析

对模块化空间可展开天线支撑桁架结构进行空间热交变环境下的热 结构分析,为天线结构因热致变形影响形面精度和网面稳定性提供合理的防护建议。采用ANSYS APDL有限元软件建立了大口径模块化空间可展开天线支撑结构的精细化数值模型,基于已有试验分别验证了模块化可展开天线结构有限元建模和热分析模型的正确性;分析了在瞬态温度场作用下约束位置等参数对支撑桁架弦杆及拉索应力的影响和热致变形规律。研究结果表明：空间可展开天线结构的应力和变形随时间历程发展与瞬态温度场变化趋势基本一致;同一瞬态温度场下,天线结构中心模块拉索热应力最大,同圈模块的弦杆热应力幅值基本相同,其上弦杆热应力逐圈增大,而拉索热应力逐圈减小;天线结构热致变形在距离约束最远端处整体累计值最大,上层中心点处累计热致变形可达15mm左右,对天线形面精度的影响不可忽略;将天线支撑桁架结构最外侧且距离结构中心最近的模块顶角和与相邻模块竖杆拼接处作为星载天线伸展臂约束时,天线结构的热致变形最小。将该处作为模块化空间可展开天线的展开支点,并建议对天线支撑结构表面采用涂刷隔热防护复合材料涂层等防护措施,以增加天线结构在太空极端环境的适应性,从而减小温度交变对天线整体形变和网面精度的影响。     

军用飞机维修保障信息系统体系结构建模研究

介绍了系统体系结构的建模方法,详细分析了系统体系结构的建模过程,针对军用飞机维修保障业务特点,对军用飞机维修保障信息系统的体系结构建模进行了研究,并给出了一个应用案例。本文的研究结果可为维修保障信息系统的研制提供参考。     

基于网络化测试技术的通信装备维修保障

未来信息化战争条件下,通信装备朝着网络化、标准化、通用化、系列化、模块化的方向发展,首先在分析现有通信装备维修保障中存在的问题和不足的基础上,提出了应用网络化测试技术的意义,并给出了系统的总体结构和两种软件设计方法;然后对现有通信装备的网络化改造提出了通过连接PC机间接接入,通过接口转换模块接入,现场智能设备嵌入TCP/IP协议三种方式,并对他们进行了分析.     

基于混合深度特征的红外目标抗干扰识别算法

复杂干扰条件下的红外空中目标识别技术是空战对抗领域的热点研究课题,复杂人工干扰严重遮蔽目标,导致目标特征的连续性与显著性遭到破坏,无法全面描述识别对象的特性,造成空中目标识别准确率下降。针对此问题,提出一种基于图像混合深度特征的空中目标抗干扰识别算法。首先,基于卷积神经网络进行图像深度特征的提取,将深度特征与梯度直方图(Histogram of Gradient, HOG)特征进行有效融合,构建混合深度特征。针对作战场景中的目标与干扰的对抗态势多样性,将支持向量机的二分类模型改进为三分类模型,对目标、干扰以及目标干扰粘连三种状态进行精确分类。实验结果表明：在复杂干扰环境下,基于混合深度特征的空中目标抗干扰识别算法正确率为92.29%,该算法可以有效地解决目标被干扰遮蔽、形成目标干扰粘连状态时的抗干扰识别问题。     

曲线保凸光顺拟合中的支持向量回归模型

几何逆向工程中的光顺曲线重构问题本质上属于回归问题,支持向量回归机是求解回归问题的新的十分有效的方法.研究用支持向量回归机处理光顺曲线的重构问题,鉴于后者有着对于光顺性的特殊要求,通过修正惩罚因子对支持向量机加以改造,即根据测量数据点的分布情况,利用各测量点圆率及保凸条件的特性确定对应的惩罚因子,从而实现了自由曲线的保凸光顺重构.数据实验也表明该方法的有效性.     

A high-performance ground-based prototype of horn-type sequential vegetable production facility for life support system in space

Vegetable cultivation plays a crucial role in dietary supplements and psychosocial benefits of the crew during manned space flight. Here we developed a ground-based prototype of horn-type sequential vegetable production facility, named Horn-type Producer (HTP), which was capable of simulating the microgravity effect and the continuous cultivation of leaf–vegetables on root modules. The growth chamber of the facility had a volume of 0.12 m³, characterized by a three-stage space expansion with plant growth. The planting surface of 0.154 m² was comprised of six ring-shaped root modules with a fibrous ion-exchange resin substrate. Root modules were fastened to a central porous tube supplying water, and moved forward with plant growth. The total illuminated crop area of 0.567 m² was provided by a combination of red and white light emitting diodes on the internal surfaces. In tests with a 24-h photoperiod, the productivity of the HTP at 0.3 kW for lettuce achieved 254.3 g eatable biomass per week. Long-term operation of the HTP did not alter vegetable nutrition composition to any great extent. Furthermore, the efficiency of the HTP, based on the Q-criterion, was 7 × 10⁻⁴ g² m⁻³ J⁻¹. These results show that the HTP exhibited high productivity, stable quality, and good efficiency in the process of planting lettuce, indicative of an interesting design for space vegetable production.     

Conceptual design of a bioregenerative life support system containing crops and silkworms

This article summarizes a conceptual design of a bioregenerative life support system for permanent lunar base or planetary exploration. The system consists of seven compartments – higher plants cultivation, animal rearing, human habitation, water recovery, waste treatment, atmosphere management, and storages. Fifteen kinds of crops, such as wheat, rice, soybean, lettuce, and mulberry, were selected as main life support contributors to provide the crew with air, water, and vegetable food. Silkworms fed by crop leaves were designated to produce partial animal nutrition for the crew. Various physical-chemical and biological methods were combined to reclaim wastewater and solid waste. Condensate collected from atmosphere was recycled into potable water through granular activated carbon adsorption, iodine sterilization, and trace element supplementation. All grey water was also purified though multifiltration and ultraviolet sterilization. Plant residue, human excrement, silkworm feces, etc. were decomposed into inorganic substances which were finally absorbed by higher plants. Some meat, ingredients, as well as nitrogen fertilizer were prestored and resupplied periodically. Meanwhile, the same amount and chemical composition of organic waste was dumped to maintain the steady state of the system. A nutritional balanced diet was developed by means of the linear programming method. It could provide 2721 kcal of energy, 375.5 g of carbohydrate, 99.47 g of protein, and 91.19 g of fat per capita per day. Silkworm powder covered 12.54% of total animal protein intakes. The balance of material flows between compartments was described by the system of stoichiometric equations. Basic life support requirements for crews including oxygen, food, potable and hygiene water summed up to 29.68 kg per capita per day. The coefficient of system material closure reached 99.40%.     

表面处理对聚酰亚胺柔性复合材料粘结性能的影响

使用聚酰亚胺(PI)膜和PI纤维编织布制备深空探测用柔性织物复合材料,研究表面处理对PI膜和PI纤维编织布之间粘结性能的影响。采用自制表面处理剂分别对PI膜和PI纤维编织布的表面进行处理,再经硅橡胶胶黏剂粘结制备柔性复合材料。使用T剥离强度试验方法测试柔性织物复合材料的层间胶接性能,并分析复合材料剥离面的形貌状态。结果显示,PI膜和PI织物的表面处理可以显著提高柔性织物复合材料的T剥离强度。其中,PI膜和PI织物未经表面处理时,柔性织物复合材料的T剥离强度为8.9 N/cm。对PI膜进行表面处理,或者对PI膜和PI织物均进行表面处理的情况下,柔性织物复合材料的T剥离强度增加至11.7 N/cm和12.8 N/cm,分别提高了31.5%和43.8%。这表明对PI膜及PI织物进行合理的表面处理,可以显著提高柔性织物复合材料的胶接性能。     

可重复使用热防护系统防热结构及材料的研究现状

在对国外有关各类航天器的防热结构和材料进行广泛调研的基础上，对陶瓷瓦、柔性毡、盖板等防热结构及材料进行了介绍，并总结了防热结构和防热材料的发展现状及趋势。