超高负荷低压涡轮非定常特性实验

针对某后加载超高负荷低压涡轮叶型的定常与非定常气动特性进行了实验研究.结果表明:由于上游尾迹的作用,在低来流雷诺数与来流湍流度下,尾迹诱导转捩叠加自然转捩可以抑制分离、降低叶型损失.在一个尾迹通过周期,由于尾迹诱导转捩的作用,附面层分离周期性地放大、缩小.同时在吸力面速度峰值点下游观测到了尾迹被割裂为两部分的现象,形成了一个主尾迹与一个副尾迹.副尾迹同样可以诱导转捩,但强度较低,对分离抑制效果有限.      

Improvement of machining accuracy in EDCM by enhanced electrochemical reaming based on a non-metallic backing layer

Electrochemical Discharge Machining (ECDM) is potentially applicable for the fabrication of film-cooling holes. However, It is extremely difficult for the holes to achieve higher precision and machining quality owing to the working liquid diminish in the lateral machining gap. In this study, a non-metallic backing layer was proposed to overcome the diminish of working liquid, and the electrochemical reaming, as a post-processing method for ECDM, was used to further improve the machining accuracy and quality of the holes. First, the three-dimensional morphology of the melted pit of a paraffin backing layer was scanned to obtain the geometric parameters. Then, simulation analysis and experimental verification of auxiliary flushing by using the non-metallic backing layer were performed. The machining performance of the holes machined with electrochemical reaming based on non-metallic backing layer was confirmed by the observations of the surface topography of the hole wall and orifice, measurement of the orifice precision, and analysis of the element composition on the surface of the orifice wall. Finally, an optimum combination of machining parameters for electrochemical reaming is obtained through a process parameter optimization experiment.     

BLI效应下整流罩设计对翼型气动特性的影响

边界层吸入(BLI)效应对飞行器气动特性的影响比较显著,而整流罩的设计会进一步影响BLI效应下的翼型气动特性。为了揭示BLI效应下整流罩的主要设计参数对翼型气动特性的影响及其原因,本文采用计算流体力学(CFD)和Morris敏感度分析相结合的方法对该问题进行了详细研究,得到了整流罩主要设计参数对翼型气动特性的敏感度排序和耦合影响程度排序;对敏感度较高和耦合影响较大的参数进行了流动分析。结果表明:在巡航和起飞2种状态下,对气动系数影响相对较大的设计参数是整流罩最大厚度和进气边界弦向位置,整流罩最大厚度对翼型气动特性影响的主要原因是整流罩背风面会发生局部分离,且其还会改变阻力-流量系数曲线的趋势;整流罩最大厚度和进气边界弦向位置对翼型气动特性的耦合影响作用较强。      

L、S频段电磁波在等离子体中衰减实验研究

利用低气压辉光放电原理在地面产生大面积、长时间稳定持续的可控等离子体,在此基础上进行了L、S频段的电波传播衰减实验,在实验室环境下持续再现了“黑障”现象,并获得了1.57GHz和2.49GHz电磁波衰减量随等离子电子密度变化的规律。将实验数据与经典传播理论以及薄层理论的预期值对比,结果表明：电波的衰减趋势与经典理论预期基本相符,验证了本文所提出的新实验方法的有效性;在等离子厚度约为波长的1倍与1.5倍条件下,未观测到明显的薄层效应。     

二次法激光加工小孔技术

为了提高激光加工航空发动机气膜冷却孔质量,介绍了一种采用焦耳级脉冲能量毫秒激光在镍基高温合金上快速加工初始通孔,再采用毫焦耳级脉冲能量纳秒激光扩孔的二次加工小孔方法。通过该方法试图消除毫秒激光加工小孔产生的再铸层以及解决纳秒激光直接加工几乎无再铸层小孔效率低、深度有限的问题,从而实现更高效率加工高质量气膜冷却孔。试验研究结果表明,该方法可以有效去除毫秒激光加工小孔孔壁的再铸层,改善孔壁表面质量,与纳秒激光直接加工小孔比较,在加工1 mm左右深的小孔时可以提高加工效率,但加工2 mm以上深度的小孔时,对提高加工效率的作用不明显。基于试验结果及分析,对二次法加工小孔提出了改进措施。     

ALGEBRAIC TURBULENCE MODEL WITH MEMORY FOR COMPUTATION OF 3-D TURBULENT BOUNDARY LAYERS WITH VALIDATION

Additional equations were found based on experiments for an algebraic turbulence model to improve the prediction of the behavior of three dimensional turbulent boundary layers by taking account of the effects of pressure gradient and the historical variation of eddy viscosity, so the model is with memory. Numerical calculation by solving boundary layer equations was carried.out for the five pressure driven three dimensional turbulent boundary layers developed on flat plates, swept-wing, and prolate spheroid in symmetrical plane. Comparing the computational results with the experimental data, it is obvious that the prediction will be more accurate if the proposed closure equations are used, especially for the turbulent shear stresses.     

再入飞行器迎风面边界层转捩的数值预估

基于求解三维Ｎａｖｉｅｒ－Ｓｔｏｋｅｓ方程,首先数值预估了高超声速三维流动的边界层特性;采用已有的高超声速三维边界层转捩准则,即在转捩位置Ｒｅθ／Ｍｅ＝常数,以及通过修正由ＯＮＥＲＡ提出的代数转捩模型,建立了预估三维边界层转捩的半经验数值技术并应用于三维Ｎａｖｉｅｒ－Ｓｔｏｋｅｓ方程的求解。利用ＨＡＬＩＳ模型及相关的实验数据,首次进行了在Ｍ∞＝６时不同雷诺数及迎角的验证试验。预估结果表明：在不考虑     

可压混合层涡并放热效应的涡动力分析

 基于双元单步不可逆燃烧动力学简化模型 ,采用紧致差分算法直接求解二维可压 Navier-Stokes方程 ,研究了时间发展非预混扩散火焰平面反应混合层流动。拟序结构由数值线性稳定性分析方法设定的粘性可压最不稳定小扰动初场促生。随放热强度增大 ,得到了基频涡卷撕裂现象。涡动力分析表明 ,放热主要通过膨胀和斜压这两种强非线性过程抑制大尺度剪切涡的演化     

光纤图像观测系统在燃烧实验中的应用

阐述了光导纤维图像观测系统的工作原理、主要部件及功能。利用该系统观测燃烧室内部不同工作状态下的火焰状况,对所记录下来的火焰图像进行了较为详细的分析,并对实验过程中出现的一些问题提出了改进措施。     

Flap contour optimization for highly integrated SERN nozzles

The performance of a Single Expansion Ramp Nozzle (SERN) for hypersonic cruise vehicles is examined with focus on the flow at the nozzle flap and the corresponding separation of the boundary layer. Two wind tunnel models are used to analyze the interaction of the free stream and the nozzle flow and the flow at the flap in detail. A finite element flow code is employed to support the design of the flap model and the analysis of the flow.Comparative contour studies show that the size and the location of the separation at the flap cowl and therefore the aerodynamic quality can be influenced by optimizing the flap cowl contour. The position of the separation is measured for different contours and varying Reynolds numbers at laminar, transitional and turbulent flow conditions. Numerical studies of a nozzle/afterbody configuration suggest an improvement of up to 3.5% in axial thrust for optimized flap contours in the examined Mach range between 1.64 and 6. At the same time the rotation of the thrust vector is reduced by up to 5° at lower Mach numbers.